Bosch MIC SERIES 500 CAMERA 500 User Manual download pdf (Page 33)

MIC Series 500 Camera Navigating the Menus | en 33

Bosch Security Systems, Inc. User’s Manual F.01U.173.601 | 2.0 | 2010.11

5.7.1 Factory Defaults

Restores the camera unit to the Factory Default settings. See Section 5.14.1 Factory Defaults,

page 49.

5.7.2 Re-map Pelco Aux (Pelco D and P Protocols only)

The Pelco protocols (D and P) support 8 different auxiliaries, but do not define what function

each should perform. This feature enables the 8 available auxiliaries to be set to any of the 8

available functions (Auto Focus, Digital Zoom, Auto Iris, Wiper, Washer, OSD and Backlight).

By default, the auxiliaries are mapped as follows:

CLEAR SOFT

STOPS

Clears any Soft stops that have been applied. RIGHT TO

CLEAR

N/A

MANUAL

CONTROL

Gives the user 10 seconds of manual control of the camera to allow the operator to move the

camera to the desired position before the menu returns to its previous state.

WASH WIPE

POSITION

Sets the wash position by pointing the camera at the washer nozzle

and pressing right to set.

RIGHT TO SET

POS

current

camera

position

SET ZERO

POS

Sets the zero degree (North) position when using the compass

direction captions. For example, point the camera North, Set Zero Pos,

resulting in the caption correctly displaying the compass heading.

RIGHT TO SET

POS

N/A

UPPER LEFT

AND LOWER

RIGHT SOFT

STOP

Soft Stops enable the user to set up an imaginary box within which the

camera can move. There is only one zone available which is defined by

first setting the Top Left and then the Bottom Right of the zone. Once

activated the MIC cannot be moved beyond the area set.

RIGHT TO SET

POS

Cleared

LEFT AND

RIGHT AUTO

PAN LIMITS

These 2 settings define the limits within which the camera will pan at

the “Auto Pan Speed” when the “Auto Pan” feature is activated.

RIGHT TO SET

POS

Cleared

MAP AUX TO

PRESET

This option opens a submenu that allows certain features of the

camera which would normally be controlled through Aux commands to

be mapped to Go To Preset commands. The features available for this

are Wiper, Washer, Digital Zoom, Auto Iris, Auto Focus, and Auto Pan.

For each function there are 3 options: Control, On Preset, and Off

Preset. The control field denotes if the function is activated by the

normal aux command or through a preset. The other 2 options set the

preset number to activate or deactivate each function. This provides

the ability to run all of the camera’s standard auxiliaries from a wider

range of control systems with varying direct aux support.

Note: If the control field of any of the functions is set to Go To Preset,

then the feature will not work using a standard button from a normal

controller. Similarly, if mapped to an Aux command, the preset values

indicated will have no effect.

WIPER,

WASHER,

DIGITAL

ZOOM,

AUTO IRIS,

AUTO FOCUS,

AUTO PAN

N/A

FIND END

STOPS

Rotates the tilt axis first down then up to its mechanical limit stops. It

then stores a “soft” limit a few units back from these for normal use.

Note: manual control is not available during this process.

RIGHT TO

START

N/A

RESET TO

DEFAULTS

Resets to the default settings for all OSD menus. CONFIRM

RESET, NO

N/A

Menu Item Description Options Default

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 55 56

Comments to this Manuals

No comments

Bosch MIC SERIES 500 CAMERA 500 User Manual Page 33

Comments to this Manuals

Related products and manuals for Security cameras Bosch MIC SERIES 500 CAMERA 500