Bosch VG5-825-ETEV Specifications Page 96
- Page / 108
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Panasonic
27-6 Camera Handler Release Notes
NP304, NF302 Picture quality is 1.3 mega pixels; there are two aspect ratios 4:3 & 16:9. MPEG-4 is not
available when 16:9 is selected
When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp
The maximum MPEG4 resolution is 1280x960. The maximum MJPEG resolution is
640x480
When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp. By
default the MPEG-4 capability is turned off programmatically which disables the audio
capability. Therefore audio is not supported.
MJPEG frame rate can be reduced if MPEG4 is manually enabled directly through the
camera’s web interface
The mode settings of H.264 and MPEG-4 operation needs to be explicitly set at the camera
Video standard has been wrongly represented in this case as video mode, which is 1.3
megapixel mode, with 4:3 and 16:9 aspect ratio settings.
Image white-balance supports 3 settings, namely
“1” – Auto White balance control mode
“2” – Auto tracking white balance mode
“3” – Auto tracking white balance under a sodium lamp mode
For NP304, it is not recommended to use audio in this model due to the camera limitation
on the number of RTSP session. Using audio might resulted in losing live video.
For NF302, at very low frame-rate settings for MPEG-4, i.e. 1fps – 3 fps it has been
observed the effective frame-rate is much lower of the order between 0.5 fps – 1.5 fps. It is
recommended to use higher frame-rate settings in these models.
NS202, NS202A By default, the MPEG-4 capability is turned off programmatically. This will effectively
disabled the audio capability, since the Panasonic handler utilizes MPEG-4 stream for audio
streaming
MJPEG frame rate can be reduced if MPEG4 is manually enabled directly through the
camera’s web interface
Number of presets supported is 64
Image white-balance supports 3 settings, namely
“1” – Auto White balance control mode
“2” – Auto tracking white balance mode
“3” – Auto tracking white balance under a sodium lamp mode
NP244, NF284 When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp
When MPEG-4 transmission is set to On, the maximum frame rate for MJPEG is 5fp. By
default the MPEG-4 capability is turned off programmatically which disables the audio
capability. Therefore audio is not supported.
MJPEG frame rate can be reduced if MPEG4 is manually enabled directly through the
camera’s web interface
Image white-balance supports 3 settings, namely
“1” – Auto White balance control mode
“2” – Auto tracking white balance mode
“3” – Auto tracking white balance under a sodium lamp mode
It is not recommended to use audio in this model due to the camera limitation on the
number of RTSP session. Using audio might resulted in losing live video.
For NP244, at very low frame-rate settings for MPEG-4, i.e. 1fps – 3 fps it has been
observed the effective frame-rate is much lower of the order between 0.5 fps – 1.5 fps. It is
recommended to use higher frame-rate settings in these models.
SC385, SW395 (SC384) Although G.711 Audio codec is available on the camera, it is not supported in this release
due to the lack of camera API support in this version of the camera firmware
The mode settings of H.264 and MPEG-4 operation needs to be explicitly set at the camera
Video standard has been wrongly represented in this case as video mode, which is 1.3
megapixel mode, with 4:3 and 16:9 aspect ratio settings.
Number of presets supported is 64
Audio stream is not working with WV-SC385, as the device is still rejecting the request to
establish an Audio only RTSP/RTP session.
Image white-balance supports 3 settings, namely
“1” – Auto White balance control mode
“2” – Auto tracking white balance mode
“3” – Auto tracking white balance under a sodium lamp mode
NP244, NF284, NS202A,
NW484, NS954, NW964,
NF302, NP304
In MPEG-4 mode, while streaming at more than 2048 Kbps these camera models only
support 1 effective stream in RTSP (Documented in “Function list of camera_encoder.pdf”
from Panasonic or Section 8.1 in “CGI Common Ref Panasonic_Network_camera
ver1.25.pdf”). Any access to camera web GUI while using the camera in NVR might result
in an error message “Too many concurrent session” displayed on camera web GUI. This
shall result in display of blue screen instead of the actual video. Selection of MJPEG in
camera web GUI should restore the video.
- VideoEdge Camera Handler 1
- Release Notes 1
- Copyright 2
- Customer Service 2
- General Purpose 3
- What’s New in This Release 5
- Continual Support 7
- American Dynamics 10
- ACTi Corporation 13
- Supported 14
- Certification 14
- Arecont Vision 15
- AXIS Communications 19
- Bosch 24
- Panasonic Corp 29
- Camera Specific Release Notes 37
- Required Ports 39
- Supported Firmware 41
- Required Network Ports 43
- Audio/Video Streaming Feature 45
- Serial Number 53
- PTZ Methods 53
- Bandwidth Efficiency 54
- Supported Resolution 58
- Error Messages 59
- Considerations 64
- Supported Resolutions 64
- Axis Communications 67
- Camera Serial Number 68
- Video/Audio Stream Feature 68
- Firmware Requirements 84
- Video Stream Feature 84
- Step Setting up a new camera 86
- Troubleshooting 89
- Panasonic 91
- Event Stream Feature 93
- Default Ports 100
- Limitations 100
- Known Issues 102
- Special Points 103
- Samsung 104
- Unsupported Key Functions 105
- Audio/Video Stream Feature 105
- Required Network Parts 105
- Supported Key Functions 105
Related products and manuals for Security cameras Bosch VG5-825-ETEV
Security cameras Bosch UPH-Z User Manual
(11 pages)
(11 pages)
Security cameras Bosch NBC-455 User Manual
(132 pages)
(132 pages)
(24 pages)
Security cameras Bosch NDN-498 User Manual
(138 pages)
(138 pages)
Security cameras Bosch MIC-71 User Manual
(32 pages)
(32 pages)
Security cameras Bosch UPH-3D User Manual
(52 pages)
(52 pages)
Security cameras Bosch VG5 User Manual
(11 pages)
(11 pages)
© 2020, manymanuals.com. All rights reserved. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals