Bosch 4410L Operations Instructions Page 15
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Checking Left 45°
Bevel Stop
1. Lower head assembly and engage head assembly
lock pin.
2. Slide head assembly completely to the back and
tighten the rail lock knob.
3. Rotate table to the 0° miter position.
4. Pull up bevel lock lever to unlock bevel.
5. Move bevel range selector knob to 45o-0° position.
(See page 28)
6. Tilt the saw assembly to the left, then rotate saw
assembly to the right until you feel the stop in the
45° left position. This is where the saw is current-
ly set for the 45° left bevel cut.
7. Use the head (remove ruler) of a combination
square to check blade at the 45 ° stop. Place the
combination square head on the table and press
it's 45 ° surface against the blade. If the blade does
not contact the full length of the square, (figure 1),
follow the calibrating procedure.
Calibrating Left 45°
Bevel Stop
1. Remove rear cover to expose bolts.
2. Lift bevel lock lever to release bevel lock.
3. Tilt saw to 45° left bevel position.
4. Remove the ruler from the combination square
and position with 45 ° surface against blade.
(Figure 1)
5. Place 10mm open-end wrench on bolt head "F".
While rotating bolt "F", watch blade tilt movement
until it is aligned with the 45° surface on combina-
tion square. (Figure 2)
6. Adjust bevel pointer to 45° line on bevel scale.
Blade
Combination Square
Table Bevel Lock
Lever
Figure 1. Left 45 ° Bevel Stop
Figure 2. Left 45 ° Bevel Adjustment
Adjusting Bevel Lock
Lever Tension
1.Lift bevel lock lever to release bevel lock.
2.Place 17mm open-end flat wrench on bolt head "E"
(Figure 2).
3.Turn nut "E" clockwise 1/8 turn to tighten bevel lock
tension or turn counter-clockwise to 1/8 turn to
loosen bevel lock tension.
4.Push down bevel lock lever until you feel the lever
snap into the locked position.
5.Verify that bevel lock tension holds the bevel posi-
tion secure and also allows bevel lock lever to lock
down to the point that a solid stop is felt.
6. If necessary, repeat steps 1-5 to adjust the tension.
15.
- Operating/SafetyInstructions 1
- General Safety Rules 2
- Safety Rules 3
- For Miter Saws 3
- Electrical Requirements 6
- Table of Contents 7
- Assembly 11
- Assembly (continued) 12
- Adjustments 13
- Adjustments (continued) 14
- Combination Square 15
- Table Bevel Lock 15
- Kerf Insert 17
- Depth Adjustment 17
- Mounting Applications 19
- Basic Saw Operations 21
- Ext:i:eo 22
- Switch Activation 23
- Miter Detent Override 24
- Microfine Miter Adjustment 24
- Base Extension 25
- Clamping lever 25
- Saw Operations 26
- Miter Cut 27
- Saw Operations (continued) 28
- Compound Cuts 29
- Cutting Base Molding 31
- Cutting Crown Molding 31
- For any Crown Molding 33
- Maintenance & Lubrication 35
- Troubleshooting 36
- TM Digital Angle 38
- TM Portable Stand with Wheels 38
- Seguridad 40
- Requisitosel ctricos 44
- Ensamblaje 49
- Colocaci6nde!pomodefijaci6n 50
- Comprobaci6ndel ajuste 51
- Calibraci6nde la hojaa 0° 51
- ComprobaciGndel topede 52
- CalibraciGndeltopede bisel 52
- Hojaen ngulo rectocon 54
- Ajustedel indicadorde la 54
- Accesoriode inserci6nparala 55
- Ajustede la profundidad 55
- Ajustede la acci6nde 56
- Aplicacionesde montaje 57
- Montajede la sierra 58
- .........l 58
- Correcto Usoincorrecto 59
- Soportede la piezadetrabajo 60
- Activaci6ndel interruptor 61
- SistemadeajusteMicrofino 62
- Cortedeslizante 64
- Cortea inglete 65
- • 0"45° 66
- Cortescompuestos 67
- Operacionesde la sierra 68
- Cortedemolduradebase 69
- Mantenimientoy lubricaci6n 73
- Cuidadode las hojas 74
- Lubricaci6nde lasherramientas 74
- Cojinetes 74
- Accesorios 76
- S curit 78
- Specifications lectriques 82
- Tabledesmati res 83
- 11 10 21 12 85
- Assemblage 87
- Montageduboutonde blocage 88
- R glages 89
- Lamed'6querrepar rapport 92
- Insertd'encoche 93
- R6glagede la profondeur 93
- Applicationsde montage 95
- Montage de la scie 96
- Guideauxiliaire 99
- Operationsde base de la scie 100
- Operationsde la scie 102
- Coupe I'onglet 103
- Coupescompos6es 105
- Coupede rainures 106
- Coupede mouluresde base 107
- Coupede moulures 107
- Maintenance et lubrification 111
- D pannage 112
- Accessoires 114
Related products and manuals for Mitre saws Bosch 4410L
Mitre saws Bosch PKS 40 Instruction Manual
(14 pages)
(14 pages)
Mitre saws Bosch 5412L Operations Instructions
(112 pages)
(112 pages)
Mitre saws Bosch PKS 40 Instruction Manual
(151 pages)
(151 pages)
Mitre saws Bosch PKS 40 Operations Instructions
(113 pages)
(113 pages)
Mitre saws Bosch 5412L Operations Instructions
(112 pages)
(112 pages)
Mitre saws Bosch CM12 Use and Care Manual
(112 pages)
(112 pages)
Mitre saws Bosch GCM12SD Use and Care Manual
(164 pages)
(164 pages)
Mitre saws Bosch CM8S Use and Care Manual
(132 pages)
(132 pages)
Mitre saws Bosch CM10GD Use and Care Manual
(164 pages)
(164 pages)
Mitre saws Bosch CM12SD Use and Care Manual
(128 pages)
(128 pages)
© 2020, manymanuals.com. All rights reserved. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals