Bosch 4410L Operations Instructions Page 32
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Saw Operations (continued)
Crown Molding Laying Flat on Table
Notes: Position workpiece with its back flat on the
saw table.
Always place top edge of molding against fence
(Decorative edge is at the bottom of crown molding.)
• "Spring angle" refers to angle between wall and
crown molding.
• Cutting crown molding flat on the table can be done
either as a chop cut or a slide cut depending on the
width of the workpiece.
1. For 90° corner, set the bevel and miter angles
using Charts below. Tighten the miter lock knob
and the bevel lock lever.
2. Position molding on saw table. Clamp workpiece in
place using the quick clamp.
Use clamping position that does not
interfere with operation. Before
switching on, lower head assembly to make sure
clamp clears guard and head assembly.
3. Follow procedures for either chop cut or slide cut
(see page 26).
4. Wait until blade comes to a complete stop before
returning head assembly to the raised position
and/or removing workpiece.
NOTE: ALWAYS TAKE A TEST CUT USING
SCRAP TO CONFIRM CORRECT ANGLES.
Quick-Action
Clamp
Crown
Molding
33.9 ° Bevel 31.6 ° Miter
Figure: Crown Molding Laying Flat
Miter and Bevel Settings for Standard Crown Molding Cuts
(When Crown Molding is Lying Flat on Table)
Assumptions: Molding is milled consistently. Corner is exactly 90° .
Molding Spring Angle is 38 degrees
Inside Corner
Left end (A)
Use the left end of the cut
Right end (B)
Use the right end of the cut
Outside Corner
Left end (C)
Use the left end of the cut
Right end (D)
Use the right end of the cut
Miter Bevel
(Table) (Tilt)
Setting Setting
(31.6) Right (33.9) Left
(31.6) Left (33.9) Right
(31.6) Left (33.9) Right
(31.6) Right (33.9) Left
Molding Spring Angle is 45 degrees
Inside Corner
Left end (A)
Use the left end of the cut
Right end (B)
Use the right end of the cut
Outside Corner
Left end (C)
Use the left end of the cut
Right end (D)
Use the right end of the cut
Miter Bevel
(Table) (Tilt)
Setting Setting
(35.3) Right (30.0) Left
(35.3) Left (30.0) Right
(35.3) Left (30.0) Right
(35.3) Right (30.0) Left
32.
- Operating/SafetyInstructions 1
- General Safety Rules 2
- Safety Rules 3
- For Miter Saws 3
- Electrical Requirements 6
- Table of Contents 7
- Assembly 11
- Assembly (continued) 12
- Adjustments 13
- Adjustments (continued) 14
- Combination Square 15
- Table Bevel Lock 15
- Kerf Insert 17
- Depth Adjustment 17
- Mounting Applications 19
- Basic Saw Operations 21
- Ext:i:eo 22
- Switch Activation 23
- Miter Detent Override 24
- Microfine Miter Adjustment 24
- Base Extension 25
- Clamping lever 25
- Saw Operations 26
- Miter Cut 27
- Saw Operations (continued) 28
- Compound Cuts 29
- Cutting Base Molding 31
- Cutting Crown Molding 31
- For any Crown Molding 33
- Maintenance & Lubrication 35
- Troubleshooting 36
- TM Digital Angle 38
- TM Portable Stand with Wheels 38
- Seguridad 40
- Requisitosel ctricos 44
- Ensamblaje 49
- Colocaci6nde!pomodefijaci6n 50
- Comprobaci6ndel ajuste 51
- Calibraci6nde la hojaa 0° 51
- ComprobaciGndel topede 52
- CalibraciGndeltopede bisel 52
- Hojaen ngulo rectocon 54
- Ajustedel indicadorde la 54
- Accesoriode inserci6nparala 55
- Ajustede la profundidad 55
- Ajustede la acci6nde 56
- Aplicacionesde montaje 57
- Montajede la sierra 58
- .........l 58
- Correcto Usoincorrecto 59
- Soportede la piezadetrabajo 60
- Activaci6ndel interruptor 61
- SistemadeajusteMicrofino 62
- Cortedeslizante 64
- Cortea inglete 65
- • 0"45° 66
- Cortescompuestos 67
- Operacionesde la sierra 68
- Cortedemolduradebase 69
- Mantenimientoy lubricaci6n 73
- Cuidadode las hojas 74
- Lubricaci6nde lasherramientas 74
- Cojinetes 74
- Accesorios 76
- S curit 78
- Specifications lectriques 82
- Tabledesmati res 83
- 11 10 21 12 85
- Assemblage 87
- Montageduboutonde blocage 88
- R glages 89
- Lamed'6querrepar rapport 92
- Insertd'encoche 93
- R6glagede la profondeur 93
- Applicationsde montage 95
- Montage de la scie 96
- Guideauxiliaire 99
- Operationsde base de la scie 100
- Operationsde la scie 102
- Coupe I'onglet 103
- Coupescompos6es 105
- Coupede rainures 106
- Coupede mouluresde base 107
- Coupede moulures 107
- Maintenance et lubrification 111
- D pannage 112
- Accessoires 114
Related products and manuals for Mitre saws Bosch 4410L
Mitre saws Bosch PKS 40 Instruction Manual
(14 pages)
(14 pages)
Mitre saws Bosch 5412L Operations Instructions
(112 pages)
(112 pages)
Mitre saws Bosch PKS 40 Instruction Manual
(151 pages)
(151 pages)
Mitre saws Bosch PKS 40 Operations Instructions
(113 pages)
(113 pages)
Mitre saws Bosch 5412L Operations Instructions
(112 pages)
(112 pages)
Mitre saws Bosch CM12 Use and Care Manual
(112 pages)
(112 pages)
Mitre saws Bosch GCM12SD Use and Care Manual
(164 pages)
(164 pages)
Mitre saws Bosch CM8S Use and Care Manual
(132 pages)
(132 pages)
Mitre saws Bosch CM10GD Use and Care Manual
(164 pages)
(164 pages)
Mitre saws Bosch CM12SD Use and Care Manual
(128 pages)
(128 pages)
© 2020, manymanuals.com. All rights reserved. | 1.304 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals