Bosch CM10GD Use and Care Manual download pdf (Page 28)



$<@6A6<; F<B? /<1F .;1 5.;1@

=?<=2?9F A< :.82 0BAA6;4 2.@62?

.;1 @.32? .69B?2 A< 3<99<D .99 6;@A?B0A6<;@

612;A63621/29<D/F/B992Al@F:/<9@:.F?2@B9A

6;@2?6<B@=2?@<;.96;7B?F@2264B?2

64B?2.;1$<@6A6<;@

• "2C2? =9.02 5.;1@ ;2.? 0BAA6;4 .?2. 22=

5.;1@ .;1 .?:@ <BA@612 A52 K"# "&L

G<;2

K"#"&L-#" – is defined as the entire table

and on the right and left side of the table and portions

of the fence within this boundry. This zone is labeled

with “No Hands” symbols placed on the fixed base.

• 2.D.?2<3A52=.A5<3A52@.D/9.12!.82.

%,%(" D6A5A52@.DK#L/F0<;1B0A6;4

. @6:B9.A21 0BAA6;4 0F092 .;1 </@2?C2 A52

=?<720A21=.A5<3A52@.D/9.1222=5.;1@

<BA<3A52=.A5<3@.D/9.12

%,N%("– It is important to know where the blade

will intersect with the workpiece during cutting

operations. Always perform the simulated cutting

sequence with the power tool switched “OFF” to gain

an understanding of the projected path of the saw

blade. Mentally note where the path of the saw blade

will fall and set up your work to keep your hands and

arms out of the path of the spinning blade. Adjust

your clamps and fences so that the smooth lower

guard and cutting action is not interfered with during

cutting operation (see Figure 30).

• <91D<?8=620236?:9F.4.6;@AA./92.;132;02

A<=?2C2;A:<C2:2;A

• 22=5.;1@6;=<@6A6<;B;A69A?6442?5.@/22;

?292.@21.;1/9.125.@0<:=92A29F@A<==21

• "2C2? =9.02 5.;1@ <; :205.;6@:

0<:=<;2;A@

• 22= 322A 36?:9F <; A52 39<<? .;1 :.6;A.6;

=?<=2?/.9.;02

• <99<D A52 :6A2? .?: D52; :6A2?6;4 923A <?

?645A  &A.;1 @9645A9F A< A52 @612 <3 A52 @.D

/9.12

'52 9<D2? 4B.?1 :.F ;<A

.BA<:.A60.99F <=2; B;12? 02?A.6;

0BAA6;4 0<;16A6<;@ 3<? 2E.:=92 D52; A?F6;4 A<

0BA D<?8=6202@ A5.A .?2 ;2.? A52 :.E6:B:

0BAA6;4 52645A 0.=.06AF (;12? A52@2 0<;16A6<;@

<? 1B?6;4 A52 /9.12 A?.C29 :<A6<; <3 0BA A52

D<?8=6202 0.; @A<= A52 9<D2? 4B.?1 :<C2:2;A

/23<?2 A52 1<D;D.?1 :<A6<; <3 A52 .?: 0<B91

=?2<=2;A529<D2?4B.?1

If this occurs:

Workpiece must be securely clamped. This frees a

hand to raise the guard by the lip just

enough to clear the workpiece (see Figure 31).

Start the saw and begin your cut.

Once you have cleared the position where the lower

guard may bind, release the guard and it will continue

to operate automatically as you cut.

64B?2%.6@6;4 <D2?B.?1

*%""

Workpiece

Lower

Guard

Lip

Clamp

$?2=.?6;43<?&.D#=2?.A6<;@

<1F.;1.;1$<@6A6<;

BM 2610027879 07-13_BM 2610027879 07-13.qxp 7/8/13 9:52 AM Page 28

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 163 164

Comments to this Manuals

No comments

Bosch CM10GD Use and Care Manual Page 28

Comments to this Manuals

Related products and manuals for Mitre saws Bosch CM10GD