Bosch CM10GD Use and Care Manual download pdf (Page 8)

'< .C<61 6;7B?F 3?<: .00612;A.9

@A.?A6;4?2:<C2=9B43?<:=<D2?

@<B?02<BA92A/23<?2:.86;4.;F.17B@A:2;A@

 &D6A05 <08# %292.@2 BAA<;@ – One of

these two buttons must be pressed before the

power switch can be pressed.

 $<D2?&D6A05 – The power switch used with the

“Lock-OFF” button energizes the unit.

 !.6; .;192 – This handle contains the power

switch. Pulling this handle down lowers the blade

into the workpiece.

 <D2? 9.12 B.?1 <D2? B.?1 6= – The

lower blade guard helps protect your hands from

the spinning blade. It retracts as the blade is

lowered. Lip can be used to raise the lower guard

in the event that the guard becomes jammed on

a workpiece.

 9.12 – Use only 10” (254 mm) diameter blades

with 5/8” (16 mm) diameter arbor holes.

 56= 23920A<? – Deflects cut-off workpieces

from entering the upper guard.

 (==2? B.?1 – Covers upper portion of the

blade.

 &9616;4 2;02 – Supports the workpiece. The

fence has a cast-in scale to make repetitive cuts

easy. The fence also has holes to secure an

auxiliary fence if desired.

 &A.A6<;.?F2;02 – Stationary fence is bolted

to the base and will support the workpiece when

the sliding fence is removed.

2?3 ;@2?A@ – Kerf inserts can be adjusted to

different blade widths to minimize workpiece

tear-out.

 !6A2?2A2;A#C2??612 – Allows detent action to

be locked out, allowing for micro-adjustments to

any miter angle.

 !6A2? <08;</ – The miter lock knob locks the

miter saw table at any desired miter angle.

 !6A2? 2A2;A 2C2? – The lever releases the

table from the detent.

 2C29 <08 2C2? – The front-positioned bevel

lock lever locks the head assembly at the desired

bevel angle.

 !6A2?&0.92!6A2?$<6;A2? – The pointer rotates

with the table and blade. It points to the miter

scale to indicate the angle setting before a cut is

made.

 !6A2? 2A2;A $9.A2 – The position of the plate

can be adjusted to set the accuracy of its detent

locations.

 !6A2?2A2;A@ – There are ten (10) miter detent

slots for fast and accurate miter cuts of common

miter angles.

 './92 – Sits in base, provides workpiece

support, rotates for desired miter cuts and

rotates the head assembly. The front extended

part of the table is called the miter arm.

 .@2 – Provides working surface to support

workpiece.

 '<<9!<B;A6;4$.1@ – The four corners of the

saw provide areas to clamp, bolt or nail the saw

to a flat work surface.



*%""

2AA6;4'<;<D,<B?!6A2?&.D

BM 2610027879 07-13_BM 2610027879 07-13.qxp 7/8/13 9:52 AM Page 8

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 163 164

Comments to this Manuals

No comments

Bosch CM10GD Use and Care Manual Page 8

Comments to this Manuals

Related products and manuals for Mitre saws Bosch CM10GD