Bosch D9412GV2 User Manual download pdf (Page 58)

D9412GV2/D7412GV2 | Operation and Installation Guide | 12.0 SDI Devices

58 Bosch Security Systems, Inc. | 5/05 | F01U003641B

12.4.1 Access

Using Wiegand style cards or tokens, the D9210B can

allow access for up to 996 cards or tokens on the

D9412GV2, and up to 396 on the D7412GV2. User

access authority can be configured to restrict access to

certain doors or to certain periods of time. The reading

of access cards, in addition to granting access, can

control whether the system disarms. Used with the

D9412GV2, the D9210B recognizes 249 master users

by user name, passcode, and access authority. The

D9210B recognizes 99 master users when used with the

D7412GV2. Each master user supports three sub-users

with unique cards or tokens having the same access

level as the master user.

12.4.2 Switch Settings

Switches on the D9210B assign a unique address (1 to

8) to each module. Table 24 shows the correct switch

setting for each D9210B address.

Table 24: Address Switch Settings for

Access Control Module

DIP Switch Settings Door Module

Addresses

1 2 3 4

1 ON ON ON ON ON

2 OFF ON ON ON ON

---------------D7412GV2 Maximum---------------

3 ON OFF ON ON ON

4 OFF OFF ON ON ON

5 ON ON OFF ON ON

6 OFF ON OFF ON ON

7 ON OFF OFF ON ON

8 OFF OFF OFF ON ON

Switch 4, Fail Safe Mode:

ON = If SDI bus fails, relay energizes.

OFF = If SDI bus fails, relay de-energizes.

Switches 5 and 6 must remain in the ON position.

12.5 SDI Address 80

SDI Address 80, available on the D9412GV2 and

D7412GV2 Control Panels, allows for two-way SDI to

RS-232 information. This address is used with home or

building automation software. A D9133 Serial Interface

Module is required for this application.

12.5.1 Serial Interface Modules (SIMs)

The DX4010i RS-232 Serial Interface Module and the

D9133 Serial Interface Module are four-wire powered

SDI devices that provide connection for RS-232

devices to the D9412GV2 and D7412GV2 Control

Panels. They use a specific communication protocol

that is provided upon request. Contact Bosch Security

Systems Technical Support Monday through Friday

from 5 AM to 5 PM EST at 888-886-6189.

The DX4010i can be installed up to 305 m (1000 ft.)

from the control panel, using 0.8 mm (22 AWG) wire.

The DX4010i was not investigated by UL. Do not use

DX4010i in UL Listed installations.

The D9133 can be installed up to 305 m (1000 ft.) from

the control panel using 1.2 mm (18 AWG) wire. The

D9133 was not investigated by UL. Do not use D9133

in UL Listed installations.

12.5.2 Address Settings

No jumper settings are required for the D9133 (SDI

Address 80) for home or building automation purposes

(Figure 26). Remove the jumper shunts for this purpose.

Figure 26: D9133 Jumper Setting for Address 80

1234

The DX4010i has specific DIP switch settings for SDI

Address 80 when home or building automation is

desired. Figure 27 on page 59 shows the correct settings

for Address 80.

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 73 74

Comments to this Manuals

No comments

Bosch D9412GV2 User Manual Page 58

Comments to this Manuals

Related products and manuals for Fire protection Bosch D9412GV2