Bosch Solution 64 Specifications download pdf (Page 34)

Solution 64

Installer Guide

Area Programming

6-2

Bosch Security Systems | 11/05 | BLCC110I

Areas > Commands >

Turn All Areas On







MENU 2-0-2

This command allows you to turn on all areas that your PIN

has been assigned to at the same time. An alternative method

for arming all areas is to enter your PIN then press an hold the

[ON] key for 2 seconds.

Enter [MENU] + [2] + [0] + [2]. The keypad will display the exit

time bar to prompt you to exit all areas. You should leave all

areas now.

When exit time has expired, the keypad will display that all

areas are turned All On (Armed).

Area 1 Name

EXIT

NOW

Note

The Display Area Icons option is programmable per keypad. If

this option has not been selected then Area icons 1 to 8 will not

be displayed. See Menu 6-1-4 — Display Area Icons.

Areas > Commands >

Turn All Areas Off







MENU 2-0-3

This command allows you to turn o all areas that your PIN has

been assigned to at the same time. This command cannot be

accessed from a keypad that is in the armed state.

Enter [MENU] + [2] + [0] + [3] to disarm all areas.

An alternative method for disarming all areas is to enter your

PIN then press an hold the [OFF] key for 2 seconds.

Areas > Commands >

Move To Area





MENU 2-0-4

Each keypad on the system can opererate any area however

you can only operate the area which is currently being

displayed. The Move to Area command allows you to change

the current keypad view from one area to another.

An alternative method for changing the current area being

displayed is to enter your PIN and then press the left or right

arrow keys. Keep pressing the arrow key until the desired area

is displayed. Only areas which have been assigned to the PIN

will be available for view.

If you move to another area the keypad will automatically

revert back to its assigned home area after 2 minutes. See

Menu 6-1-3, Home Area.

Enter [MENU] + [2] + [0] + [4] and select the area from the list

and press [OK] to move to the selected area.

A001 Security System

A002 Area 2 Name

A003 Area 3 Name

Press  OK or MENU

Note

Turn o option Menu 6-1-4, Pin To change Area and use the [←]

and [→] keys to move through all areas on the system without

the need to enter your pin.

Areas > Commands >

Chime On/Off









MENU 2-0-5

Chime mode allows you to monitor a zone (or group of zones)

by sounding the keypad buzzer or activating a programmable

output. This can be useful when you need to monitor the front

or back entrance to a premises while in the disarmed state.

To select which zones will be monitored for chime see Menu 3-

0-3 — Set Chime Zones.

To turn chime mode On or O enter [MENU] + [2] + [0] + [5]

and select the area from the list then press [OK].

Security System A001

Chime is OFF

To turn ON, Press ON

To Go Back Press OK

Note

The Chime Tone will only be heard on keypads programmed to

sound the chime tone. See Menu 6-1-5 — Chime Tone

Area Properties

Areas > Area Properties >

Area Name





MENU 2-1-0

A r e a 1 N a m e

This menu allows you to program the name for each area. Each

area name can be programmed with up to 16 characters. At

factory default, only Area 1 is used. The Solution control panel

can have a maximum of 8 independent areas programmed.

Enter [MENU] + [2] + [1] + [0] and select the area from the list

and press [OK].

Area Name A001

Security System

Press  OK to SAVE

Use the arrow and number keys to move and change text.

When the Area Name is complete, press [OK]. At any time you

can press the [OFF] key to clear the text from the current cursor

position to the end of the line.

Note

See Alpha Text section in Section 4 - Programming Overview for

further detail on entering alpha text.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 34

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64