Bosch Solution 64 Specifications download pdf (Page 70)

Solution 64

Installer Guide

Comms Programming

9-8

Bosch Security Systems | 11/05 | BLCC110I

 RAS Allowed

Callback Verify

 Abort RAS On Alarm

Press  OK ON OFF MENU

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

RAS Allowed

This option allows you to congure the panel via the

SolutionLink RAS upload/download software using a PC.

There are two dierent methods of connection avialable;

Direct Connect – via serial cable.

Remote Connect – via telephone line.

Note

See Direct Link and SolutionLink RAS Upload/Download

programming in Section 5 — Programming Overview for more

information.

Call Back Verification Required

Setting this option will force the panel to use call back verication for

all remote SolutionLink RAS sessions. See MENU 5-3-0 — Call back

Number for more information.

Terminate RAS On Alarm

If this option is programmed, the RAS connection between the panel

and the remote upload / download computer will be terminated if

panel registers an alarm that needs to be reported.

Answering Machine Bypass

Answering machine bypass allows you to establiish a RAS connection

to a panel when there is an answering machine or facsimile machine

connected on the same telephone line.

Using SolutionLink call the paneland let the phone ring no

more than 4 times before hanging up.

Wait a minimum of 8 seconds (but no more than 60 seconds)

before calling the panel again. This time the panel will answer

the incoming call as soon as it registers the rst ring and the

connection will be established.

Answer Incoming Call Only If Armed

Setting this option will prevent the panel from answering an

incoming call unless at least one area on the system is armed. If all

areas are o the panel will not answer the call. This option would be

useful in a busy oce when due to the large volume of incomming

calls answering machine bypass may not be eective.

Remote Program Editing Only When Disarmed

Setting this option will prevent a SolutionLink RAS connection to the

panel while any are is armed.

Allow ‘User Functions’ Via Remote Access Software

Setting this option allows access to user functions via the RAS upload/

download software. If this option is not programmed, user functions

will be disabled.

Report RAS Start / End Sessions

Setting this option will cause the panel to report the start and end of

RAS programming sessions to the base station and the history log.

Comms > Remote Access >

DTMF Options



MENU 5-3-5

1 DTMF Arming Y

2 DTMF Disarming N

3 DTMF User Functions N

4 DTMF Quick Arm ([0] + [#]) Y

5 Reserved N

6 Reserved N

7 Reserved N

8 Reserved N

Press [MENU] + [5] + [3] + [5]. The keypad will display the

current DTMF options.

 DTMF Arming

DTMF Disarming

DTMF User Functions

Press  OK ON OFF MENU

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

DTMF Arming

Setting this option enables user to remotely arm one or more areas

on the panel using their PIN and a touch tone phone. This option

requires the Solution Interactive Voice module to be tted.

DTMF Disarming

Setting this option enables users to remotely disarm one or more

areas on the panel using their PIN and a touch tone telephone. This

option requires the Solution Interactive Voice module to be tted.

DTMF User Functions

Setting this option enables access to user DTMF functions using their

PIN and a touch tone telephone. This option requires the Solution

Interactive Voice module to be tted.

DTMF Quick Arm

Setting this option allows users and control room operators to

remotely arm the system using a touch tone phone without the need

for a PIN.

To arm the system call the number which the panel is connected

to and when the panel answer you will here 3 beeps in accending

frequency if the panel is in the disarmed condition. Press [0] + [#] to

arm. You will hear 3 beeps in decending order when the panel arms.

Note

All areas on the system will be armed regardless of there

condition when using the DTMF quick arm function.

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 70

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64