Bosch Solution 64 Specifications download pdf (Page 91)

Solution 64

Installer Guide

System Programming

Bosch Security Systems | 11/05 |

11-7

System Power Options

System > Power >

AC Options



MENU 7-3-0

1 Display AC Fail Y

2 Report AC Fail Y

3 Use AC To Synchronise The System Clock Y

4 Random AC Report 2hour N

5 AC Fail After 1 hour N

6 Reserved N

7 Reserved N

8 Display Clock Trouble Y

This menu option allows you to congure the AC Mains Power

system options.

(*** System Wide Parameter ***)

Press [MENU] + [7] + [3] + [0]. The keypad will display the

current AC Options.

 Display AC fail

 Report AC Fail

 Sync Clock To AC

Press  OK ON OFF MENU

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

Display AC Fail

Setting this option will cause the panel to ash the Mains Power

icon as soon as the AC power supply has failed. If the power remains

missing continiously for 1 minute then a system trouble will be

registered on the keypad. When the AC power supply returns to

normal the Mains Power icon will remain on steady. If this option is

disabled then the system will not ash the Mains Power icon and no

system trouble will occur.

Report AC Fail

Setting this option will cause the panel to report an AC Fail to the base

station if the mains power has been missing for a period of 1 minute.

A restore report will be sent once the mains power has been restored

for one minute.

Synchronise System Clock to AC

Setting this option allows the panel to syncronise its internal clock

with the mains frequency (50hz). This option should be set unless the

panel is being used in an area where the mains power is unreliable.

Random AC Reporting 2hr

Setting this option allows the panel to randomly delay (up to 2 hours)

the AC Fail report. This option is used to prevent multiple Solution-

128 panels from reporting AC fail at the same time and should be left

disabled when using the Solution 64 panel.

Extend AC Fail To 1 Hour

Setting this option will cause the panel to only send an AC Fail report

to the base station if the power has been missing continuously for one

hour. The Mains Power icon will operate as normal.

Display Clock Trouble

Setting this option will cause the panel to show a Date and Time

System trouble if the power is removed from the system for any

period of time such as when performing a system upgrade or service

work. If this option is disabled then no system trouble will appear and

you will need to remember to set the correct time when you re power

the system.

System > Power >

Battery Options



MENU 7-3-1

1 Display Battery Fail Y

2 Report Battery Fail Y

3 Execute Battery Testing On Arming Y

4 Arming Allowed On Low Battery Y

5 Reserved N

6 Reserved N

7 Reserved N

8 Reserved N

This menu option allows you to congure the standby Battery

system options. The system is constantly monitoring the

battery condition with a dynamic battery test carried out every

4 hours.

(*** System Wide Parameter ***)

Press [MENU] + [7] + [3] + [1]. The keypad will display the

current Battery Options.

 Display Battery Fail

 Report Battery Fail

 Battery Test On Arming

Press  OK ON OFF MENU

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

Display Battery Fail

Setting this option will cause the keypad to display a Trouble

condition when the panel detects that the standby battery is

disconnected or that its voltage is low. The trouble condition will

clear as soon as the panel has measured the battery voltage is 12.5

volts or greater.

Report Battery Fail

Setting this option will cause the panel to send a Low Battery report

to the base station when it measures the battery voltage has dropped

below 11.5 volts. A Low Battery Restore report will be sent when the

panel detects that the battery voltage is above 12.5 volts.

If the panel fails to detect the battery, or if it measures the battery

voltage below 10.2 volts, then a Battery Test Failed report will be sent.

A Battery Test restore will be sent when the battery is re-connected or

replaced.

Execute Battery Testing On Arming

Setting this option will cause the panel to perform an additional

dynamic battery test each time Area 1 is armed All On.

1 2 ... 86 87 88 89 90 91 92 93 94 95 96 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 91

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64