Bosch D9112B Installation Manual Page 84
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9112B | Program Entry Guide | EN | 84
Bosch Security Systems | 2/04 | 74-06145-000-D
A# Force Armed
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when the specified area is Force Armed. It
remains activated until the area is disarmed or the
panel is reset. (Perimeter arming and disarming does
not affect this relay.)
A# Watch Mode
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when a perimeter point is tripped in the
specified area while the area is in Watch Mode. It
remains activated for two seconds.
A# Area Armed
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
This relay activates when the specified area begins
the master arming sequence. The relay remains
activated until the area is disarmed. Entry delay does
not reset this relay.
A typical application for this relay is to control an
“Armed” LED on a keyswitch.
If multiple areas use the same relay, the relay sets
when the last area begins the arming sequence. It
resets when the first area disarms.
A# Area Fault
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates whenever a perimeter or interior point is
faulted. The relay remains activated until all
perimeter and interior points in the area are normal,
bypassed or force armed.
A typical application for this relay is to control a
“faulted point” LED on a keyswitch to indicate that
the area is not ready to arm.
A# Duress
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when a duress alarm is generated from a
command center assigned the specified area. A
Burg
Time
must be programmed in Bell Parameters. The
relay provides steady output and remains active until
the bell time expires or the panel is reset.
Duress is a panel-wide function which is enabled in
the Passcode Worksheet. Reporting can be
suppressed by Authority Level.
A# Keypad Fail
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when a supervised command center
assigned to the area fails (does not respond when the
address is polled). The relay remains activated until
the command center responds. There may be a short
delay between the time the command center fails or
restores and the relay response.
A# Perim Fault
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when a perimeter point assigned to the
specified area is faulted. This relay activates
regardless of the area’s armed state. This relay
provides a steady output until all perimeter points in
the area are normal, bypassed or force armed.
Any point programmed for
Point Type
“1” causes
this relay to respond when the point is opened,
shorted, or missing.
A# Silent Alarm
Default: Blank
Selection: Blank, 1 to 128, A, B, or C
Activates when a point assigned to the specified area
and programmed for
Silent Bell
causes an alarm
response.
Burg Time
must be programmed in Bell
Parameters. The relay provides steady output and
remains active until the bell time expires or the
panel is reset.
Point Index
Silent Bell
YES, causes this relay to
respond when the point goes into alarm.
- Control Panel 1
- About this Guide 2
- Other Lettering Conventions 2
- Used in this Manual 2
- Table of Contents 3
- Table of Tables 7
- 1.0 Panel Wide Parameter 8
- Point/User Flag 9
- A# Acct O/C 9
- A# Area O/C 9
- P### BFSK/Relay 9
- Modem Format 10
- Default: 11
- 1.2 Phone Routing 12
- 1.3 Power Supervision 19
- 1.4 Printer Parameters 20
- PRT Non Alrm 21
- SDI Fail 21
- Diagnostic 21
- Expanded Test 21
- 1.5 RAM Parameters 22
- Log % Full 24
- RAM Call 24
- Bad Call to RAM 24
- 2.0 Area Wide Parameters 25
- 2.2 Bell Parameters 27
- 2.3 Opening and Closing 29
- 2.4 O/C Windows 35
- Xept Holiday 39
- W## Xept Holiday 39
- 2.5 Command Center 42
- CF# Text 44
- CF# Key Stroke 44
- Program Record Sheet 44
- 3.0 User Interface 45
- 3.3 Cmd Center Function 46
- 3.4 Authority Lvl Assign 46
- Point Type 51
- Perimeter O/C 51
- Perimeter 51
- Closing Options 60
- 4.0 Command Menu 62
- 5.0 User Access Windows 64
- Windows 65
- 6.0 Passcode Worksheet 66
- Usr Code Tamper 67
- 7.0 Point Index 69
- Response 70
- Point Response 70
- P## Entry Delay 70
- 72
- A# Burg Time 74
- Fire Point 74
- 1. Program point 75
- 2. Choose a 75
- 3. Enable and/or disable 75
- 8.0 Point Assignments 79
- 8.2 Command 9 80
- 8.3 Command 7 81
- 9.0 Relay Parameters 82
- 9.1 Area Wide Relays 83
- 9.2 Panel Wide Relays 85
- 10.0 Skeds 86
- S## Area 1 87
- Bypassable 88
- Unbypass Point 88
- Unbypass All 88
- S## Defer Test 90
- S## Hourly Report 90
- S## Defer Status 90
- S## Cmd Center 91
- S## Custom Func 91
- 11.0 Holiday Indexes 94
- 11.2 View Holidays 95
- Bosch Security Systems 96
- 130 Perinton Parkway 96
- Fairport, NY 14450-9199 96
Related products and manuals for Security access control systems Bosch D9112B
(5 pages)
(8 pages)
(2 pages)
(12 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.244 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals