Bosch Solution 64 Specifications download pdf (Page 36)

Solution 64

Installer Guide

Area Programming

6-4

Bosch Security Systems | 11/05 | BLCC110I

Pulse Count Handover Allowed

This option allows zones from the same area that have both pulse

count and pulse count time programmed the ability to hand over

pulses to other pulse count zones during their respective pulse count

time. Only zones that have an active pulse count time can accept

pulse count handover from another zone.

Burglary delay zones can only handover pulses to other burglary

delay zones. Burglary instant and/or handover zones can handover

pulses to other burglary instant and/or handover zones. 24 hour

non-re zone types can only handover pulses to other 24 hour non

re zones. A 24-hour re zone can only handover pulses to another

24-hour re zone.

Senior Watch

This option requires at least one burglary zone in the corresponding

area to be faulted and restored during the senior watch time. If no

burglary zone has register during the senior watch time, the keypad

will sound an alarm.

To warn the user that senior watch time is about to expire, the keypad

will sound the auto arm pre-alert time (if programmed) prior to

sounding the alarm. See MENU 7-2-6 — Senior Watch Time.

This feature is not applicable when the corresponding area is turned

All On.

An output (Output Event Type 51) can be programmed to operate as

follow Senior Watch if required.

Areas > Properties >

Output Options



MENU 2-1-3

1 Arm/Disarm Speaker Beeps Via RF Keyfob Y

2 Arm/Disarm Speaker Beeps Via Keyswitch Y

3 Siren / Strobe When Part On Allowed Y

4 Alarm On PIN Retry Violations Y

5 Alarm On Exit Error N

6 Alarm On Keyswitch Tamper ( Only If System Armed) Y

7 Reserved N

8 Reserved N

The above options are programmable per area.

Enter [MENU] + [2] + [1] + [3] and select the area from the list

then press [OK].

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

 SPK Beeps Keyfob

 SPK Beeps Key/SW

 SPK Strobe Part ON

Press  OK ON OFF MENU

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

Arm/Disarm Speaker Beeps Via RF Key Fob

This option allows audible beeps via the speaker output to verify to

the user that they have successfully turned the area On or O using

the RF keyfob. The speaker output will sound One beep for O, two

beeps for On and three beeps for Part On.

Arm/Disarm Speaker Beeps Via Keyswitch

This option allows audible beeps via the speaker output to verify to

the user that they have successfully turned the area On or O using

a Keyswitch. The speaker output will sound One beep for O, two

beeps for On.

Siren / Strobe When Part On Allowed

This option allows the strobe and audible alarms to operate when the

system is turned Part On or Part 2 On mode.

Alarm On PIN Retry Violations

When the PIN Retry Count as programmed in Menu 1-5-1 is reached

an audible alarm will occur.

Alarm On Exit Error

This option allows you to sound an alarm when an exit error occurs.

An exit error occurs when an entry/exit delay zone becomes unsealled

during exit delay time and remains unsealled at the end of exit delay

time. If this happens, the entry delay will start. If the area is not

turned o (disarmed) before the entry delay time expires an alarm will

occur.

Alarm On Keyswitch Tamper

This option allows you to sound an alarm when a tamper condition

occurs on a zone programmed as a Keyswitch Zone.

Refer to Menu 3-1-1 — Zone Type in Section 8 - Input Programming

for information on programming zones to be a keyswitch input.

Areas > Properties >

Reporting Options



MENU 2-1-4

1 Report PIN Retry Y

2 Report Exit Error Y

3 Smart Lockout N

4 Reserved N

5 Cancel Reports Y

6 Reserved N

7 Open / Close Reports For Part On N

8 Open / Close Reports Only After Alarm N

The above options are programmable per area.

Enter [MENU] + [2] + [1] + [4] and select the area from the list

then press [OK].

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

 Report PIN Retry

 Report Exit Error

Smart Lockout

Press  OK ON OFF MENU

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

Report PIN Retry

When the PIN Retry Count as programmed in Menu 1-5-1 is reached a

Wrong Code Entry alarm report will be sent to the Control Room.

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 36

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64