Bosch Solution 64 Specifications download pdf (Page 58)

Solution 64

Installer Guide

Output Programming

8-6

Bosch Security Systems | 11/05 | BLCC110I

Outputs > Properties >

Output Polarity



MENU 4-1-3

0 0

The output polarity programs how the output will operate.

Only one option (0 – 15) can be programmed per output. See

the Output Polarity description for more detailled information.

Press [MENU] + [4] + [1] + [3] and use the up and down arrows

to highlight the output in the list and press [OK]. The keypad

will display the current output polarity.

Output Polarity Op001

14 - Speaker Output

Press 0-9 OK to SAVE

Use the up and down arrow keys to select the Output Polarity

required then Press [OK] to save and exit or press [MENU] to

exit without saving.

Option Polarity

0 Normally Open Going Low

1 Normally Open Going Low With Pre Delay

2 Normally Open Latching Low

3 Normally Open Pulsing Low

4 Normally Open One Shot Low

5 Normally Open One Shot Low + Retrigger

6 Normally Open One Shot Low + Reset

7 Normally Low Going Open

8 Normally Low Going Open With Pre Delay

9 Normally Low Latching Open

10 Normally Low Pulsing Open

11 Normally Low One Shot Open

12 Normally Low One Shot Open + Retrigger

13 Normally Low One Shot Open + Reset

14 Horn Speaker (Output 1 or 2 Only)

15 Reserved

Table 18: Output Polarity Types

Normally Open Going Low

Output is normally open circuit and switches to GND when the event

occurs. The output will reset when the output event restores. Time

parameters do not apply to this polarity type.

Normally Open Going Low With Pre Delay

Output is normally open circuit and switches to GND when the event

occurs provided the time parameter has expired. The output will reset

when the output event restores. Time parameters will only set the Pre

Delay when this polarity is selected.

Normally Open Latching Low

Output is normally open circuit and will switch to zero volts when

the event occurs. The output can only be reset manually using the

Output Command Menu.

Normally Open Pulsing Low

Output is normally open circuit and will pulse LOW when the event

occurs. The output will reset when the output event restores. Use the

Time Parameter to set the pulse duration.

Normally Open One Shot Low

Output is normally open circuit and switches to GND when the event

occurs. The output will only reset when the time specied in the Time

Parameter expires. The output will run for the full duration and cannot

be manually reset.

Normally Open One Show Low + Retrigger

Output is normally open circuit and switches to GND when the event

occurs. The output will retrigger each time the event occurs. The

output will reset when the one shot time has expired.

This polarity is ideally suited for security lighting control. A sensor

can be used to trigger an output event and then each time the senso

triggers, the output will operate. The light will turn o when the one

shot timer expires.

Normally Open One Shot Low + Reset

Output is normally open circuit and will switch to GND when the

event occurs. The output will reset when the one shot timer expires or

when the event has restored. This means the operation of the output

can be shortened based on the event and or the programmed time

parameter.

Normally Low Going Open

Output is normally GND and will switch to open circuit when the

event occurs. The output will reset when the output event restores.

Time parameters do not apply to this polarity type.

Normally Low Going Open With Pre Delay

Output is normally GND and will switch to open circuit when the

event occurs provided the time parameter has expired. The output

will reset when the output event restores. Time parameters will only

set the Pre Delay when this polarity is selected.

Normally Low Latching Open

Output is normally GND and will switch to open circuit when the

event occurs. The output can only be reset maually usning the output

Command Menu.

Normally Low Pulsing Open

Output is normally LOW and will pulse OPEN when the event occurs.

The output will reset when the output event restores. Use the Time

Parameter to set the pulse duration.

Normally Low One Shot Open

Output is normally LOW and will switch to open circuit when the

event occurs. The output will only reset when the time specied in

the Time Parameter expires. The output will run for the full duration

and cannot be manually reset.

Normally Low One Show Open + Retrigger

Output is normally LOW and will switch to open circuit when the

event occurs. The output will retrigger each time the event occurs.

The output will reset when the one shot time has expired.

Normally Low One Shot Open + Reset

Output is normally LOW and will switch to open circuit when the

event occurs. The output will reset when the one shot timer expires

or the event has restored. This means the operation of the output

can be shortened based on the event and or the programmed time

parameter.

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 58

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64