Bosch Solution 64 Specifications download pdf (Page 71)

Solution 64

Installer Guide

Comms Programming

Bosch Security Systems | 11/05 | BLCC110I

9-9

Comms > Remote Access >

Voice Access Code



MENU 5-3-6

9 #

This option sets a 2 digit code which is used to access the panel

from any internal phone connected to the same telco line as

the panel. For this option to work, a CM100 Voice Module must

be connected to the panel.

This default number may need to be changed depending on

the country and or telco exchange / PABX system being used.

Make sure that when the code is entered, no external phone

services are selected or activated. If they are, then change the

code to something else.

It is important to realise that this code is only used to start

the connection process. Once a connection is established, the

voice module will ask the user to enter their PIN before they

will be able to control the panel. The Voice Access Code is

shared by all users who need this type of access to the panel.

See the CM100 documention for more details.

Press [MENU] + [5] + [3] + [6]. The keypad will display the

current DTMF options.

Voice Access Code N001

Press 0-9 OK to SAVE

Using the numeric keys enter the new Voice Access Code then

press [OK] to save and exit or press [MENU] to exit without

saving.

Comms > Remiote Access >

CLI Number



MENU 5-3-7

First

Number

1 Digits 32

Second

Number

1 Digits 32

Third

Number

1 Digits 32

CLI Numbers (Call Line Identication) allows the Solution

control panel to answer an incoming call only when the

control panel identies that the incoming call is from any one

of the three CLI numbers programmed. Up to three dierent

CLI telephone numbers can be programmed, each having a

maximum of 32 digits.

Enter [MENU] + [5] + [3] + [7]. The keypad will display

information for CLI number 1.

CLI Number 1

Press  0-9 OK to SAVE

Using the numeric keys, enter all the digits for CLI number 1.

You can change a single digit by scrolling the cursor left or

right. For special characters including, pause, * or #, use the

up and down arrow keys.

Press [OK] to program CLI number 2.

CLI Number 2

Press  0-9 OK to SAVE

Using the numeric keys, enter all the digits for CLI number 2 .

Press [OK] to program CLI number 3.

When nished Press [OK] to save and exit or press [MENU] to

exit without saving.

Note

Up to 3 Phone numbers can be entered for CLI Call Line

Identication for remote access detection. You must enter STD

code plus the compete number for this option to work. Press

[OK] after each telephone number is entered to save and move

to the next number.

Reporting Options

Comms > Dialler Reporting >

TX Format Dest 1



MENU 5-4-0

0 = Disable 1

1 = Contact ID 7 = Domestic

2 = SIA 8 = Voice 13 = Reserved

3 = Serial STU 9 = Panel 1 (Node 1) 14 = Reserved

4 = GSM 10 = Panel 2 (Node 2) 15 = Reserved

5 = WEB MAIL 11 = Panel 3 (Node 3)

6 = SMS 12 = Panel 4 (Node 4)

This menu allows you to program the transmission format

or language the panel will use to send event reports to

Destination 1. The panel has two separate destinations

that reports can be sent to and each one can be set to use a

dierent transmission format depending on the application.

At factory default, all reports are routed to Destination 1.

Press [MENU] + [5] + [4] + [0]. The keypad will display the

current Transmission Format for Destination 1.

TX Format Dest 1 N001

01-Contact ID

Press 0-9 OK to SAVE

Use the up and down arrow keys to select the Transmission

Format required then Press [OK] to save and exit or press

[MENU] to exit without saving.

Note

Transmission Formats 9 -12 are not applicable on the Solution

64 control panel and should not be programmed. Other

formats may require additional hardware or add on modules to

function.

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 71

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64