Bosch 6000 Installation Manual Page 117
- Page / 170
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Solution-144
Installation Manual Comms Programming
9-19
Bosch Security Systems 10/12 BLCC600BI
Comms > IP Reporting >
Poll Rate
MENU 5-6-2
0 0 3 0
Seconds x 10
This menu allows the installer to program how often the
control panel sends a signal to the base station receiver
via Destination 1 and/or Destination 2. The poll interval
programmed in seconds and then multiplied by 10 (eg.
0009 = 90 sec's / 0360 = 1 hr / 4320 = 12 hrs and 8640 =
24 hrs). This should be set so that the control panel sends
a poll to the base station receiver at least once within the
polling time required.
1) Press [MENU] + [5] + [6] + [2]. The keypad will
prompt you to select which destination
(destination 1 or 2) that you want to program the
poll rate.
Rr1 Dest 1
Rr2 Dest 2
Exit
Press
OK or MENU
2) Highlight the destination number (1 or 2) required,
then press [OK]to select.
3) The keypad will display the current poll rate.
Poll Rate Rr1
0030 Seconds
Press 0-9 OK to SAVE
4) Use the numeric keys [0] to [9] to program the new
poll rate in seconds (0000 to 9999 seconds x 10),
then press [OK] to save and exit or press [MENU] to
exit without saving.
Comms > IP Reporting >
ACK Wait Time
MENU 5-6-3
0 1 0
Seconds
This menu allows the installer to program the
acknowledge wait time in seconds for both Destination 1
and/or Destination 2. The acknowledge wait time can be
programmed between 1 and 255 seconds (0 = Disabled).
1) Press [MENU] + [5] + [6] + [3]. The keypad will
prompt you to select which destination
(destination 1 or 2) that you want to program the
acknowledge wait time.
Rr1 Dest 1
Rr2 Dest 2
Exit
Press
OK or MENU
2) Highlight the destination number (1 or 2) required,
then press [OK]to select.
3) The keypad will display the current acknowledge
wait time.
Ack Wait Time Rr1
010 Seconds
Press 0-9 OK to SAVE
4) Use the numeric keys [0] to [9] to program the new
acknowledge wait time in seconds (000 to 255),
then press [OK] to save and exit or press [MENU] to
exit without saving.
Comms > IP Reporting >
IP Format
MENU 5-6-4
00 - Conettix 0 1
01 - Conettix NNC (Anti Replay)
02 - CSV IP ALARM
03 - Suretek (TBA)
04 - Permacom (TBA)
05 - Direct Wireless (TBA)
06 - MyAlarm CID (TBA)
This menu allows the installer to program which IP format
the control panel will report to the base station receiver.
1) Press [MENU] + [5] + [6] + [4]. The keypad will
prompt you to select which destination
(destination 1 or 2) that you want to program the
acknowledge wait time.
Rr1 Dest 1
Rr2 Dest 2
Exit
Press
OK or MENU
2) Highlight the destination number (1 or 2) required,
then press [OK]to select.
3) The keypad will display the current IP format.
IP Format Rr1
01 - Conettix NNC
Press
0-9 OK to SAVE
4) Use the numeric keys [0] to [9] to program the new
IP format required, then press [OK] to save and exit
or press [MENU] to exit without saving.
- Solution 144 1
- TELEPERMIT 2
- CONTENTS 3
- SECTION 5 4
- ACCESS PROGRAMMING 4
- SECTION 6 5
- AREA PROGRAMMING 5
- SECTION 7 6
- INPUT PROGRAMMING 6
- SECTION 8 7
- OUTPUT PROGRAMMING 7
- SECTION 9 9
- COMMS PROGRAMMING 9
- SECTION 10 10
- DEVICE PROGRAMMING 10
- SECTION 11 12
- SYSTEM PROGRAMMING 12
- Overview 15
- Installing the Hardware 17
- Wiring Diagrams 25
- VISION-GRAPhIC 29
- Figure 25: Wiring Diagram 30
- Programming Overview 31
- Programming Overview 33
- = All (No PIN Required) 37
- Access Programming 43
- Press OK to Delete Token 47
- John Smith 47
- Area Programming 55
- Area 1 Name 56
- Area Programming 61
- Input Programming 67
- Input Programming 68
- 00 - No Area 72
- Output Programming 83
- Output Programming 84
- O u t p u t 1 N a m e 86
- 0 0 0 0 0 0 0 0 0 0 0 0 92
- Hour Minute Seconds 10 92
- Comms Programming 99
- Comms Programming 102
- 1 Digits 32 107
- 0 0 0 0 0 0 0 0 111
- Receiver IP 116
- Receiver Port 116
- ACK Wait Time 117
- IP Format 117
- Poll Rate 117
- Retry Count 118
- Encryption Key 118
- Conettix NNC 118
- IP Address 120
- IP RAS Options 121
- RAS Lockout Time 121
- 00 - Log Events Only 0 1 124
- 01 - Dest 1 + Log 124
- 02 - Dest 2 + Log 124
- 03 - Dest 1 & 2 + Log 124
- 04 - Dest 2 If 1 Fails 124
- Device Programming 125
- Device Programming 126
- Security System 130
- DISARMED 130
- Module IP Address 138
- Subnet Mask 138
- Default Gateway 138
- Module MAC Address 138
- Ethernet Options 138
- Solution-144 140
- System Programming 141
- System Programming 142
- Programming Examples 159
- Specifications 163
- Accessories 164
- SECTION 14 165
- Installation Manual Index 166
Related products and manuals for Coffee grinders Bosch 6000
(55 pages)
Coffee grinders Bosch 6000 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 2.009 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals