Bosch 6000 Installation Manual download pdf (Page 88)

Solution-144



Installation Manual  Output Programming

8-6

Bosch Security Systems 10/12 BLCC600BI

26 – Entry Timing

This event type will cause the output to operate while

either Entry Timer 1, Entry Timer 2 or the Part Mode Entry

Timer is active. The output will reset when the entry

timer expires or the corresponding area is disarmed.

27 – Exit Timing

This event type will cause the output to operate while

Exit Timer is active. The output will reset when the exit

timer expires or the corresponding area is disarmed.

28 – End Of Exit Time

This event type will cause the output to operate

when the Exit Time expires and will reset when the

corresponding area is disarmed.

29 – Chime On

This event type will cause the output to operate when

Chime Mode is activated and will reset when Chime

Mode is turned oﬀ.

If the event assignment for this output is set to zero (all

areas), then the output will operate as soon as Chime

Mode is activated in any area and will reset when Chime

Mode is turned oﬀ in all areas.

30 - Chime Zone Trigger

This event type will cause the output to operate when

a speciﬁc Chime Zone is triggered and reset when the

Chime Zone reseals.

If the event assignment for this output is set to zero (all

areas), then the output will operate as soon as any chime

zone is triggered provided that Chime Mode is on in

those areas. The output will reset when all Chime Zones

are resealed. For this event type to work Chime Mode

must be turned on. See MENU 2-0-5 — Chime On/Oﬀ

Note

It also allows the output to reset when chime mode

is turned oﬀ by the user even if the chime zone is still

faulted. It also allows if one or more chime zones

remain faulted after the one shot timer has expired,

the output programmed for chime will operate or

retrigger if another chime zone becomes faulted.

31 – Auto Arm Pre Alert

This event type will cause the output to operate when

the Auto Arm Pre-Alert Timer is active and will reset

when the Pre-Alert Timer expires or a valid user code is

entered.

Note

The output will also reset when the auto arm pre-

alert time has been delayed by by the user .

32 – Ready To Arm All On

This event type will cause the output to operate when

the area is disarmed and all zones in the area are sealled.

The output will reset when the area is armed or when a

zone becomes unsealed.

If the event assignment for this output is set to zero (all

areas), then the output will only operate if all areas are

disarmed and all zones are sealed. The output will reset if

any area is armed or if any zone becomes unsealed.

33 – Ready To Part Arm

This event type will cause the output to operate when

the area is disarmed and all zones in the area which are

to be monitored in Part On mode are sealed. The output

will reset when the area is armed or when a Part On zone

becomes unsealled.

If the event assignment for this output is set to zero (all

areas), then the output will only operate if all areas are

disarmed and all Part On zones are sealed. The output

will reset if any area is armed or if any Part On zone

becomes unsealed.

34 – Ready To Part 2 Arm

This event type will cause the output to operate when

the area is disarmed and all zones in the area which

are to be monitored in Part 2 On mode are sealled. The

output will reset when the area is armed or when a Part 2

On zone becomes unsealed.

If the event assignment for this output is set to zero (all

areas), then the output will only operate if all areas are

disarmed and all Part 2 On zones are sealed. The output

will reset if any area is armed or if any Part 2 On zone

becomes unsealed.

35 – Close Sent OK

This event type will cause the output to operate when

the Closing report has been acknowledged (Kissed-Oﬀ )

by the control room receiver. The output will reset when

the area is disarmed. If the output has been assigned to

multiple areas then it will only reset when all areas have

been disarmed.

36 – External Audible

This event type will cause the output to operate when

any audible alarm occurs. The output will reset when the

system or area is disarmed.

This event type will also generate speaker beeps

when the system or area is armed via a RF Keyfob, the

Programmable Input Terminal or Keyswitch zone.

 1 beep when the area is disarmed

 2 beeps when the area is armed All On

 3 beeps when the area is armed Part On

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 169 170

Comments to this Manuals

No comments

Bosch 6000 Installation Manual Page 88

Comments to this Manuals

Related products and manuals for Coffee grinders Bosch 6000