Bosch 6000 Installation Manual download pdf (Page 75)

Solution-144



Installation Manual  Input Programming

7-9

Bosch Security Systems 10/12 BLCC600BI

Inputs > Zone Properties >

Door Assignment



MENU 3-1-5

0 0

00 - No Door Assignment

01 - Door 1 Name 09 - Door 9 Name

02 - Door 2 Name 10 - Door 10 Name

03 - Door 3 Name 11 - Door 11 Name

04 - Door 4 Name 12 - Door 12 Name

05 - Door 5 Name 13 - Door 13 Name

06 - Door 6 Name 14 - Door 14 Name

07 - Door 7 Name 15 - Door 15 Name

08 - Door 8 Name 16 - Door 16 Name

This menu allows the installer to assign a zone to a single

door. There are 16 different doors available.

1) Press [MENU] + [3] + [1] + [5] and use the up and

down arrows to highlight the Zone in the list then

press [OK]. Alternatively, you can enter the zone

number directly and press [OK]. The keypad will

display the current door assignment.

Door Assignment Zn1

00 - No Door Assignment

Press  0-9 OK to SAVE

2) Use the up and down arrows to select the door that

you want to assign the zone to.

3) Press [OK] to save and exit or press [MENU] to exit

without saving.

Inputs > Zone Properties >

Report Route



MENU 3-1-6

00 - Log Events Only 0 1

01 - Dest 1 + Log

02 - Dest 2 + Log

03 - Dest 1 & 2 + Log

04 - Dest 2 If 1 Fails

This menu sets the Zone Report Route or Report

Destination for each individual zone in the system. All

events such as alarms and troubles for each zone will be

reported according to this menu setting. Each zone can

only be assigned to one report route from the list above.

1) Press [MENU] + [3] + [1] + [6] and use the up and

down arrows to highlight the Zone in the list then

press [OK]. Alternatively, you can enter the zone

number directly and press [OK]. The keypad will

display the current Zone Report Route.

Report Route Zn1

01 - Dest 1 + Log

Press  0-9 OK to SAVE

2) Use the up and down arrows to select the Report

Route that you want to assign the zone to.

3) Press [OK] to save and exit or press [MENU] to exit

without saving.

Note

At factory default all Zones are set to report to

Destination 1 and the System Log. See the Zone

Default Table for more information on Zone default

settings.

Inputs > Zone Properties >

Report Options



MENU 3-1-7

1 Lockout Dialler Y

2 Report Alarm Y

3 Report Troubles Y

4 Report Bypass Y

5 Reserved N

6 Reserved N

7 Report Restores Y

8 Delay Reporting N

The above options are programmable per zone.

1) Press [MENU] + [3] + [1] + [7] and use the up and

down arrows to highlight the Zone in the list then

press [OK]. Alternatively, you can enter the zone

number directly and press [OK]. The keypad will

display the Report Options for the currently

selected zone.

2) Use the up and down arrow keys to highlight the

option then press the [ON] key to enable or the

[OFF] key to disable.

 Lockout Dialler

 Report Alarm

 Report Troubles

Press  OK ON OFF MENU

3) Repeat Step 2 until all options are programmed as

required, then press [OK] to save and exit or press

[MENU] to exit without saving.

Lockout Dialler

Setting this option will enable Dialler Lockout

functionality for the respective zone(s). All zones in

the system can be individually programmed for Dialler

Lockout.

When enabled the zone will be allowed to transmit

alarm reports each time it is triggered provided that

the Swinger Dialler count has not been reached. If the

zone is triggered and the Swinger Dialler count has been

reached then the zone will become locked out and no

further reports will be sent for that zone. Dialler lockout

will be reset on the next arming cycle.

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 169 170

Comments to this Manuals

No comments

Bosch 6000 Installation Manual Page 75

Comments to this Manuals

Related products and manuals for Coffee grinders Bosch 6000