Bosch 6000 Installation Manual Page 63
- Page / 170
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Solution-144
Installation Manual Area Programming
6-9
Bosch Security Systems 10/12 BLCC600BI
Exit Time A1
060 Seconds
Press 0-9 OK to SAVE
3) Using the numeric keys, enter the required entry
time in seconds. Valid times are 1 - 255 seconds, 0
= No Exit Time.
4) Press [OK] to save and exit or press [MENU] to exit
without saving.
Areas > Timers >
Entry Time 1
-
MENU 2-8-1
0 2 0
Seconds
This menu allows the installer to set the entry delay time
for each area. The entry delay time can be programmed
between 0 and 255 seconds. This should be set to allow
the user enough time to turn the area off (disarm) before
an alarm condition occurs (eg. end of entry time = alarm).
The entry delay timer starts as soon as a user faults a zone
programmed as burglary delay 1 (eg. opens the front
door) after the area has been turned on and the exit delay
timer has expired.
1) Press [MENU] + [2] + [8] + [1]. The keypad will
display a list of areas.
A1 Security System
A2 Area 2 Name
A3 Area 3 Name
Press OK or MENU
2) Highlight the area required to change, then press
[OK] to select. The keypad will display the current
entry time set for the area selected.
Entry Time 1 A1
020 Seconds
Press 0-9 OK to SAVE
3) Using the numeric keys, enter the required entry
time in seconds. Valid times are 1 - 255 seconds, 0
= No exit time.
4) Press [OK] to save and exit or press [MENU] to exit
without saving.
Areas > Timers >
Entry Time 2
-
MENU 2-8-2
0 4 0
Seconds
This menu allows the installer to set the entry delay time
for each area. The entry delay time can be programmed
between 0 and 255 seconds. This should be set to allow
the user enough time to turn the area off (disarm) before
an alarm condition occurs (eg. end of entry time = alarm).
The entry delay timer starts as soon as a user faults a zone
programmed as burglary delay 2 (eg. opens the back
door) after the area has been turned on and the exit delay
timer has expired.
1) Press [MENU] + [2] + [8] + [2]. The keypad will
display a list of areas.
A1 Security System
A2 Area 2 Name
A3 Area 3 Name
Press OK or MENU
2) Highlight the area required to change, then press
[OK] to select. The keypad will display the current
entry time set for the area selected.
Entry Time 2 A1
040 Seconds
Press 0-9 OK to SAVE
3) Using the numeric keys, enter the required entry
time in seconds. Valid times are 1 - 255 seconds, 0
= No entry tTime.
4) Press [OK] to save and exit or press [MENU] to exit
without saving.
Areas > Timers >
Part Entry Time
-
MENU 2-8-3
0 6 0
Seconds
This menu sets the time period which a keypad will sound
its warning tone after a zone is triggered in Part On or Part
2 On modes. The user must disarm the area before the
Part Entry Time expires, otherwise an alarm condition will
be triggered.
At factory default, when an area has been turned Part On
or Part 2 On and exit time has finished, violating a non 24hr
burglary zone will start the part entry time. The keypad
will sound the hi/lo tone for a period of 60 seconds before
the control panel sound an alarm or until the user turns
the area off.
- Solution 144 1
- TELEPERMIT 2
- CONTENTS 3
- SECTION 5 4
- ACCESS PROGRAMMING 4
- SECTION 6 5
- AREA PROGRAMMING 5
- SECTION 7 6
- INPUT PROGRAMMING 6
- SECTION 8 7
- OUTPUT PROGRAMMING 7
- SECTION 9 9
- COMMS PROGRAMMING 9
- SECTION 10 10
- DEVICE PROGRAMMING 10
- SECTION 11 12
- SYSTEM PROGRAMMING 12
- Overview 15
- Installing the Hardware 17
- Wiring Diagrams 25
- VISION-GRAPhIC 29
- Figure 25: Wiring Diagram 30
- Programming Overview 31
- Programming Overview 33
- = All (No PIN Required) 37
- Access Programming 43
- Press OK to Delete Token 47
- John Smith 47
- Area Programming 55
- Area 1 Name 56
- Area Programming 61
- Input Programming 67
- Input Programming 68
- 00 - No Area 72
- Output Programming 83
- Output Programming 84
- O u t p u t 1 N a m e 86
- 0 0 0 0 0 0 0 0 0 0 0 0 92
- Hour Minute Seconds 10 92
- Comms Programming 99
- Comms Programming 102
- 1 Digits 32 107
- 0 0 0 0 0 0 0 0 111
- Receiver IP 116
- Receiver Port 116
- ACK Wait Time 117
- IP Format 117
- Poll Rate 117
- Retry Count 118
- Encryption Key 118
- Conettix NNC 118
- IP Address 120
- IP RAS Options 121
- RAS Lockout Time 121
- 00 - Log Events Only 0 1 124
- 01 - Dest 1 + Log 124
- 02 - Dest 2 + Log 124
- 03 - Dest 1 & 2 + Log 124
- 04 - Dest 2 If 1 Fails 124
- Device Programming 125
- Device Programming 126
- Security System 130
- DISARMED 130
- Module IP Address 138
- Subnet Mask 138
- Default Gateway 138
- Module MAC Address 138
- Ethernet Options 138
- Solution-144 140
- System Programming 141
- System Programming 142
- Programming Examples 159
- Specifications 163
- Accessories 164
- SECTION 14 165
- Installation Manual Index 166
Related products and manuals for Coffee grinders Bosch 6000
(55 pages)
Coffee grinders Bosch 6000 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 6.352 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals