Bosch 6000 Installation Manual download pdf (Page 148)

Solution-144



Installation Manual  System Programming

11-8

Bosch Security Systems 10/12 BLCC600BI

System > Power >

Battery Options



MENU 7-3-1

1 Display Battery Fail Y

2 Report Battery Fail Y

3 Battery Test On Arming Y

4 OK To Arm Low Battery Y

5 Reserved N

6 Reserved N

7 Reserved N

8 Reserved N

(*** System Wide Parameter ***)

This menu option allows you to configure the standby

Battery system options. The system is constantly

monitoring the battery condition with a dynamic battery

test carried out every 4 hours.

1) Press [MENU] + [7] + [3] + [1]. The keypad will

display the current Battery Options.

 Display Battery Fail

 Report Battery Fail

 Battery Test On Arming

Press  OK ON OFF MENU

2) Use the up and down arrow keys to highlight the

option then press the [ON] key to enable or the

[OFF] key to disable.

3) Repeat Step 2 until all options are programmed as

required, then press [OK] to save and exit or press

[MENU] to exit without saving.

Display Battery Fail

Setting this option will cause the keypad to display

a Trouble condition when the panel detects that the

standby battery is disconnected or that its voltage is low.

The trouble condition will clear as soon as the panel has

measured the battery voltage is 12.5 volts or greater.

Report Battery Fail

Setting this option will cause the panel to send a Low

Battery report to the base station when it measures

the battery voltage has dropped below 11.5 volts. A

Low Battery Restore report will be sent when the panel

detects that the battery voltage is above 12.5 volts.

If the panel fails to detect the battery, or if it measures

the battery voltage below 10.2 volts, then a Battery Test

Failed report will be sent. A Battery Test restore will be

sent when the battery is re-connected or replaced.

Battery Test On Arming

Setting this option will cause the panel to perform an

additional dynamic battery test each time Area 1 is

armed All On.

OK To Arm Low Battery

Setting this option will allow the system to be armed

even though the panel currently has a low battery

condition.

When this option is disabled, the panel will not arm

if there is a low battery condition or if the battery is

missing. The user will be notiﬁed of the system trouble

on the keypad and they will need to have the fault

rectiﬁed before the system or area can be armed.

System > Power >

Fuse Options



MENU 7-3-2

1 Display COMM+ O/Load Y

2 Report COMM+ O/Load Y

3 Display +12v O/Load Y

4 Report +12v O/Load Y

5 Display LAN O/Load Y

6 Report LAN O/Load Y

7 Reserved N

8 Reserved N

(*** System Wide Parameter ***)

This menu option allows you to configure the Fuse related

system options.

1) Press [MENU] + [7] + [3] + [2]. The keypad will

display the current Fuse Options.

 Display COMM+ O/Load

 Report COMM+ O/Load

 Display +12v O/Load

Press  OK ON OFF MENU

2) Use the up and down arrow keys to highlight the

option then press the [ON] key to enable or the

[OFF] key to disable.

3) Repeat Step 2 until all options are programmed as

required, then press [OK] to save and exit or press

[MENU] to exit without saving.

Display COMM+ O/Load

Setting this option allows the keypad to display a system

trouble message when the current load on the COMM +

terminal exceeds its maximum rating of 3 Amps.

Report COMM+ O/Load

Setting this option will cause the panel to send an

Overcurrent Trouble report to the base station when

the current load on the COMM + terminal exceeds its

maximum rating of 3 Amps.

1 2 ... 143 144 145 146 147 148 149 150 151 152 153 ... 169 170

Comments to this Manuals

No comments

Bosch 6000 Installation Manual Page 148

Comments to this Manuals

Related products and manuals for Coffee grinders Bosch 6000