Bosch 6000 Installation Manual Page 142
- Page / 170
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Solution-144
Installation Manual System Programming
11-2
Bosch Security Systems 10/12 BLCC600BI
There are no
System troubles
Press OK or MENU
5) Press [OK] or [MENU] when finished.
i
Note
When in stand-by mode keypads will display system
trouble events on the third line of the display.
SYSTEM TROUBLE MESSAGES
The following list shows the systems trouble messages
including a description of what has caused the trouble
event to occur. System Trouble events are also recorded in
the System Event Log.
Power Missing
This trouble message will display when the AC mains
power supply to the panel is disconnected or failled and
will clear when the power is reconnected. The Mains
Power Icon in the keypad will also flash when the power
is missing.
AC Missing
The control panel has detected that the AC mains supply
has failed or is disconnected on an optional universal
expander or LAN power supply module.
Battery Low
This trouble message will display if the panel’s backup
battery voltage has dropped below 11.5 volts DC during
a battery test and will clear when the voltage is above
12.5 volts during a subsequent battery test.
Battery Missing
This trouble message will display if the panel detects
that the system’s backup battery is missing or has been
disconnected.
Low Battery
The control panel has detected that an RF sensor has a
low battery condition. Replace the RF sensor battery and
transmit an RF signal to clear the low battery condition.
Box Tamper
The control panel has detected that the tamper circuit on
the LAN power supply module is faulted. Place a shunt
across the tamper input pins or close the tamper circuit
to clear the box tamper trouble condition.
Temperature Alert
The control panel has detected that the console (eg.
keypad, LAN reader or fingerprint reader) has exceeded
the global temperature high or temperature low settings.
Receiver Missing
This trouble message will display if the panel detects the
RF receiver is missing or disconnected. The trouble will
clear when the receiver is reconnected.
Case Tamper
This trouble message will display if the panel detects that
the tamper circuit on the RF receiver is faulted.
Receiver Jam
This trouble message will display if the connected RF
receiver detects RF noise levels that may prevent it from
working correctly.
Comms Fail Route1
This trouble message will display if the panel has failed
to send pending reports to Report Destination 1. All
possible call attempts will be made before the trouble
message is displayed.
Comms Fail Route2
This trouble message will display if the panel has failed
to send pending reports to Report Destination 2. All
possible call attempts will be made before the trouble
message is displayed.
Sensor Watch Alert
The control panel has detected a zone has failed to
detect a change of state within the sensor watch period.
Comms BUSS Trble
This trouble message will display if the panel failed to
communicate to a system device which is connected to
the LAN bus (e.g. keypad etc).
Default PIN Trble
This trouble message will display if the panel detects
that either the Installer PIN or User 1 PIN is still set to the
factory default PIN. Change the PIN to clear the fault.
Date & Time
This trouble message will display if the system date and
time has not been set. Program the correct date and time
to clear the fault.
Cabinet Tamper
This trouble message will display if the panel detects that
it’s cabinet tamper input is faulted. Close the tamper
switch to clear the fault.
Connection Trouble
The control panel has detected that an output device (eg.
external siren etc) has failed or has been disconnected
from the system.
Overload Condition
The control panel has detected that an output has an
over current condition.
- Solution 144 1
- TELEPERMIT 2
- CONTENTS 3
- SECTION 5 4
- ACCESS PROGRAMMING 4
- SECTION 6 5
- AREA PROGRAMMING 5
- SECTION 7 6
- INPUT PROGRAMMING 6
- SECTION 8 7
- OUTPUT PROGRAMMING 7
- SECTION 9 9
- COMMS PROGRAMMING 9
- SECTION 10 10
- DEVICE PROGRAMMING 10
- SECTION 11 12
- SYSTEM PROGRAMMING 12
- Overview 15
- Installing the Hardware 17
- Wiring Diagrams 25
- VISION-GRAPhIC 29
- Figure 25: Wiring Diagram 30
- Programming Overview 31
- Programming Overview 33
- = All (No PIN Required) 37
- Access Programming 43
- Press OK to Delete Token 47
- John Smith 47
- Area Programming 55
- Area 1 Name 56
- Area Programming 61
- Input Programming 67
- Input Programming 68
- 00 - No Area 72
- Output Programming 83
- Output Programming 84
- O u t p u t 1 N a m e 86
- 0 0 0 0 0 0 0 0 0 0 0 0 92
- Hour Minute Seconds 10 92
- Comms Programming 99
- Comms Programming 102
- 1 Digits 32 107
- 0 0 0 0 0 0 0 0 111
- Receiver IP 116
- Receiver Port 116
- ACK Wait Time 117
- IP Format 117
- Poll Rate 117
- Retry Count 118
- Encryption Key 118
- Conettix NNC 118
- IP Address 120
- IP RAS Options 121
- RAS Lockout Time 121
- 00 - Log Events Only 0 1 124
- 01 - Dest 1 + Log 124
- 02 - Dest 2 + Log 124
- 03 - Dest 1 & 2 + Log 124
- 04 - Dest 2 If 1 Fails 124
- Device Programming 125
- Device Programming 126
- Security System 130
- DISARMED 130
- Module IP Address 138
- Subnet Mask 138
- Default Gateway 138
- Module MAC Address 138
- Ethernet Options 138
- Solution-144 140
- System Programming 141
- System Programming 142
- Programming Examples 159
- Specifications 163
- Accessories 164
- SECTION 14 165
- Installation Manual Index 166
Related products and manuals for Coffee grinders Bosch 6000
(55 pages)
Coffee grinders Bosch 6000 User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 0.225 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals