Bosch 150 AC Specifications Page 100
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
100
• DOK-DIAX01-MAIN+2AD+1M-ANW1-EN-E1,44 • 07.97
4. Diagnostics and Fault Clearance
4.2 Fault Diagnostics
The red „FAULT“ LED comes on. The fault messages appear in the
display. The fault messages must be cancelled with the red accept key
after the fault has been remedied (reset).
Cause:
Plug connector X7 on the CDR board in the control unit has been fitted
with an ADW2 analogue speed command value interface.
Remedy:
Switch off the control unit. Replace ADW2 with ADW3. Contact Indramat
customer service!
Cause:
• Bleeder monitor has tripped due to overheating.
• The bleeder in the control unit is faulty or no bleeder has been fitted.
Remedy:
• Check whether the bleeder resistor in the upper part of the control unit
is faulty (visual inspection). If the bleeder is OK, then allow for the
cooling-down period (approximately 15 minutes).
• If the control unit is not fitted with the "additional bleeder" option, <256>
is incorrectly contained in the value of FUNCT2 (A06).
Cause:
The limiting current in the control unit set on the electronic cut-out has
been exceeded.
Remedy:
Check the motor cable for a short-circuit or earth fault. Check the motor
for shorted windings or earth fault.
Cause:
Error on the CDR board.
Remedy:
Switch control unit off. Replace CDR board. Contact Indramat customer
service!
Cause:
The DC bus circuit is not charging up properly when the power contactor
is energized.
Remedy:
• Check supply cable is securely connected to mains terminal.
• Remove possible short-circuit in the DC bus circuit (L+,L-) (KDA/TDA
and RAC2 only).
• Otherwise, contact Indramat customer service!
Cause:
Earth fault in motor cable or DC bus circuit.
Remedy:
Switch off control unit. Check motor cable (cabinet cable entry gland?)
and replace if necessary. Check motor. With KDA, check the DC bus
wiring.
BLEEDER
BS (KDA only)
DACFAULT
DC-FAULT
ADW2
EARTH CON
- Spindle Motors 1
- Overview of Sections 3
- About this documentation 5
- About this document 6
- Contents 10
- Spindle Drives 13
- INDRAMAT 15
- 1.2 Safety Guidelines 16
- 1.3 The Equipment Required 18
- Checking the drive 19
- Condition of wiring 19
- Cross sections of power 19
- Operating the drive with the 22
- Checking the speed/ 22
- 2. Operating the Controllers 27
- Operating mode switch 28
- R 5 3 1 2 1 29
- Switching into parameter 31
- Reading a parameter record 32
- Changing to another 32
- Display Definition 33
- Possible fault 35
- Possible fault messages 36
- 3. Controller Functions 37
- 3.2 Speed Command Value 38
- X2 control inputs 39
- Drehzahlsollwert 39
- Function conversion 41
- Speed limits 41
- Binary Coding 42
- Speed command value 42
- Floating-Point Coding 43
- Possible error message in 43
- Drehzahlsollwertrampen 45
- Instructions for using the 47
- Conversion formula (alterna 47
- 3.5 Command Value Smoothing 48
- Smoothing time constant 49
- 3.6 Spindle Positioning 50
- Spindelpos Standard 52
- Changing the direction of 53
- Direction of positioning 53
- 3600 spindle positions 54
- Entering position command 54
- Priority of the position 54
- Para-Spindel-3600 55
- Positioning accuracy 56
- Para-Spindel-refer 57
- Display: 59
- Torque build-up 62
- Ramp function 62
- Speed dependent 63
- Braking without overshoot 63
- P-GAIN data: 64
- of tacho filter: 64
- Follow-up time T 64
- of the speed controller: 64
- C-axis functions 65
- Conversion of functions 66
- Weighting conversion speed 66
- 3.9 Power and Torque Limits 67
- Limiting with parameter or 68
- Changeover capability of the 68
- A) Percentage torque 69
- B) Torque utilization related 70
- C) Power level related to 70
- General data on the 71
- D) Torque value 71
- Para-Analo 72
- X2 signal outputs 73
- Temperaturvorwarnun 74
- 0 = fault 76
- Umschaltung-Para 77
- Switchable function 78
- 3.15 Gear Change 79
- Gear stage dependent drive 80
- Functional sequence 81
- Possible error messages on 81
- Sequence of operations 84
- 3.16 Two-Motor Changeover 85
- Possible error messages in 86
- 3.17 Master-Slave Operation 88
- Slave drive data 89
- Formula: 90
- Para-NOT-AUS 93
- (KDA, TDA) 95
- OSCILATE 99
- N<NMIN 99
- POS ORDER 99
- 4.2 Fault Diagnostics 100
- RSKCURNT (RAC 3 only) 105
- S-CIRCUIT 105
- 5. Overview of Parameters 106
- Additions list ! 108
- Para-umschaltbar 109
- Additions list! 110
- Parameter protocol! 111
- Para-M03 113
- Parameter-Blatt 115
- X2 Control inputs 116
- Signal outputs 116
- Analogue outputs 116
- 19 and terminals 1 and 2 117
- (option) 118
- 1 = acceptance of current N 119
- 6.4 SERCOS Interface (option) 120
- X6 with KDA/TDA; X13 with RAC 121
- X6 with KDA/TDA 122
- X13 with RAC 122
- 6.7 Serial Interface (option) 123
- 6.8 Motor Feedback Connection 124
- ( 400 125
- mA ) 125
- 7. Index 126
- Anschlußplan für 82 129
- < > 137
- Type code fields: 139
- TDA 1.1 - 100 - 3 - A00 139
- Figure 121: Type codes for AS 143
- High-resolution 145
- Indramat 146
Related products and manuals for Power tools Bosch 150 AC
Power tools Bosch GTA500 User Manual
(12 pages)
(12 pages)
Power tools Bosch 52314 Specifications
(44 pages)
(44 pages)
Power tools Bosch CRS180 Specifications
(44 pages)
(44 pages)
Power tools Bosch SG450AF Specifications
(32 pages)
(32 pages)
Power tools Bosch 1617EVSPK Specifications
(68 pages)
(68 pages)
Power tools Bosch POF 1200 AE Specifications
(98 pages)
(98 pages)
Power tools Bosch POF 1200 AE Specifications
(11 pages)
(11 pages)
Power tools Bosch GTL2 User Manual
(36 pages)
(36 pages)
Power tools Bosch GHO 26-82 Specifications
(11 pages)
(11 pages)
Power tools Bosch DWM 40 L User Manual
(104 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 2.209 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals