Bosch 150 AC Specifications Page 57
- Page / 146
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
• DOK-DIAX01-MAIN+2AD+1M-ANW1-EN-E1,44 • 07.97
57
3. Controller Functions
Para-Spindel-refer
Parameter protocol!
☞
Parameter
P16
P15
Designation
PQ-FUNCT
P-MAXRPM
Function
rotational direction of motor and spindle
spindle reference switch signal to X2/37
Note: invalid value
Here: spindle speed for searching
the reference switch signal
Value range or value
< 0 >
< 2 >
< 64 >
< 65 > !
1.....24000
S R Q
- same
- opposite
1/min
S R Q
The sign of the reference switch search speed (P MAXRPM) corresponds
to the sign of the speed command value that applies when positioning is
initiated (control input RUN 1->0). If the speed command value at the
time has to be switched to zero by the controller, then positive or negative
speed can be set for locating the reference switch signal.
• The reference switch signal from the spindle must be connected to the
EXT POS control input.
• The angle a
min
is the minimum ≥° of the spindle reference switch. The
maximum reference point detection error is given by the angle a
min
and
the hysteresis of the spindle reference switch.
The affect of the hysteresis can be eliminated, if the reference switch
signal is always searched for in the same direction. In this case, the
speed command value must always have the same sign when
positioning is initiated.
•a
min
depends on the search speed of the reference point on the spindle.
Search speed is the value of parameter P-MAXRPM.
Reference switch search
direction
3.6.3 Spindle Positioning via Motor Feedback with Spindle
Reference Switch
Figure 42: Additional parameters for spindle positioning via motor feedback
Information about the
spindle reference switch
- Spindle Motors 1
- Overview of Sections 3
- About this documentation 5
- About this document 6
- Contents 10
- Spindle Drives 13
- INDRAMAT 15
- 1.2 Safety Guidelines 16
- 1.3 The Equipment Required 18
- Checking the drive 19
- Condition of wiring 19
- Cross sections of power 19
- Operating the drive with the 22
- Checking the speed/ 22
- 2. Operating the Controllers 27
- Operating mode switch 28
- R 5 3 1 2 1 29
- Switching into parameter 31
- Reading a parameter record 32
- Changing to another 32
- Display Definition 33
- Possible fault 35
- Possible fault messages 36
- 3. Controller Functions 37
- 3.2 Speed Command Value 38
- X2 control inputs 39
- Drehzahlsollwert 39
- Function conversion 41
- Speed limits 41
- Binary Coding 42
- Speed command value 42
- Floating-Point Coding 43
- Possible error message in 43
- Drehzahlsollwertrampen 45
- Instructions for using the 47
- Conversion formula (alterna 47
- 3.5 Command Value Smoothing 48
- Smoothing time constant 49
- 3.6 Spindle Positioning 50
- Spindelpos Standard 52
- Changing the direction of 53
- Direction of positioning 53
- 3600 spindle positions 54
- Entering position command 54
- Priority of the position 54
- Para-Spindel-3600 55
- Positioning accuracy 56
- Para-Spindel-refer 57
- Display: 59
- Torque build-up 62
- Ramp function 62
- Speed dependent 63
- Braking without overshoot 63
- P-GAIN data: 64
- of tacho filter: 64
- Follow-up time T 64
- of the speed controller: 64
- C-axis functions 65
- Conversion of functions 66
- Weighting conversion speed 66
- 3.9 Power and Torque Limits 67
- Limiting with parameter or 68
- Changeover capability of the 68
- A) Percentage torque 69
- B) Torque utilization related 70
- C) Power level related to 70
- General data on the 71
- D) Torque value 71
- Para-Analo 72
- X2 signal outputs 73
- Temperaturvorwarnun 74
- 0 = fault 76
- Umschaltung-Para 77
- Switchable function 78
- 3.15 Gear Change 79
- Gear stage dependent drive 80
- Functional sequence 81
- Possible error messages on 81
- Sequence of operations 84
- 3.16 Two-Motor Changeover 85
- Possible error messages in 86
- 3.17 Master-Slave Operation 88
- Slave drive data 89
- Formula: 90
- Para-NOT-AUS 93
- (KDA, TDA) 95
- OSCILATE 99
- N<NMIN 99
- POS ORDER 99
- 4.2 Fault Diagnostics 100
- RSKCURNT (RAC 3 only) 105
- S-CIRCUIT 105
- 5. Overview of Parameters 106
- Additions list ! 108
- Para-umschaltbar 109
- Additions list! 110
- Parameter protocol! 111
- Para-M03 113
- Parameter-Blatt 115
- X2 Control inputs 116
- Signal outputs 116
- Analogue outputs 116
- 19 and terminals 1 and 2 117
- (option) 118
- 1 = acceptance of current N 119
- 6.4 SERCOS Interface (option) 120
- X6 with KDA/TDA; X13 with RAC 121
- X6 with KDA/TDA 122
- X13 with RAC 122
- 6.7 Serial Interface (option) 123
- 6.8 Motor Feedback Connection 124
- ( 400 125
- mA ) 125
- 7. Index 126
- Anschlußplan für 82 129
- < > 137
- Type code fields: 139
- TDA 1.1 - 100 - 3 - A00 139
- Figure 121: Type codes for AS 143
- High-resolution 145
- Indramat 146
Related products and manuals for Power tools Bosch 150 AC
Power tools Bosch GTA500 User Manual
(12 pages)
(12 pages)
Power tools Bosch 52314 Specifications
(44 pages)
(44 pages)
Power tools Bosch CRS180 Specifications
(44 pages)
(44 pages)
Power tools Bosch SG450AF Specifications
(32 pages)
(32 pages)
Power tools Bosch 1617EVSPK Specifications
(68 pages)
(68 pages)
Power tools Bosch POF 1200 AE Specifications
(98 pages)
(98 pages)
Power tools Bosch POF 1200 AE Specifications
(11 pages)
(11 pages)
Power tools Bosch GTL2 User Manual
(36 pages)
(36 pages)
Power tools Bosch GHO 26-82 Specifications
(11 pages)
(11 pages)
Power tools Bosch DWM 40 L User Manual
(104 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 1.533 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals