Bosch Solution 64 Specifications download pdf (Page 44)

Solution 64

Installer Guide

Input Programming

7-4

Bosch Security Systems | 11/05 | BLCC110I

Inputs > Commands >

Smoke Sensor Reset







MENU 3-0-5

This command allows you to reset smoke sensors. When

initiated this command will cause any outputs programmed as

Event Type 49 — Smoke Sensor GND in the chosen area to turn

o for 10 seconds.

Enter [MENU] + [3] + [0] + [5] and use the up and down arrows

to highlight the area that you want to reset the smoke

detectors in then press [OK].

Smoke detector reset in

Progress. Please wait

The keypad will automatically return to the menu when all

smoke detectors in the area has been reset.

Note

Smoke detectors must have the negative power terminal

connected to an output programmed as Event Type 49 for this

command to work.

Zone Properties

Inputs > Zone Properties >

Zone Name





MENU 3-1-0

Z o n e 1 N a m e

This menu allows you to program the name for each zone.

Zone names can be up to 16 characters long.

Enter [MENU] + [3] + [1] + [0] and use the up and down arrows

to highlight the Zone in the list then press [OK]. Alternatively,

you can enter the zone number directly and press [OK].

User the arrow and number keys to move and change text.

When the Zone Name is complete, press [OK]. At any time you

can press the [OFF] key to clear the text from the current cursor

position to the end of the line.

Zone Name Zn001

Zone 1 Name

Press  OK to SAVE

Note

See Alpha Text Programming in Section 4 - Programming

Overview for further detail on entering alpha text.

Inputs > Zone Properties >

Zone Type



MENU 3-1-1

This menu allows you to congure the zone type or behaviour

for every zone in the system. Each zone should be assigned

to a Zone Type that denes the way in which the panel will

respond when an alarm is triggered on that zone. Refer to

the table and descriptions below for the available Zone Type

selections.

Zone Types

0 = Zone Not Used

1 = Burglary Delay 1 (Entry Timer 1)

2 = Burglary Delay 2 (Entry Timer 2)

3 = Burglary Instant 1 (With Exit Delay)

4 = Burglary Instant 2 (No Exit Delay)

5 = Burglary Handover

6 = Burglary 24-Hour

7 = Tamper 24-Hour

8 = Hold Up 24-Hour (Silent & Invisible)

9 = Medical 24-Hour

10 = Panic 24-Hour

11 = Fire 24-Hour

12 = Reserved

13 = Keyswitch Zone

14 = Display Only

15 = 24-Hour Non Burglary

Table 17: Zone Types

Press [MENU] + [3] + [1] + [1] and use the up and down arrows

to highlight the Zone in the list then press [OK]. Alternatively,

you can enter the zone number directly and press [OK].

Use the up and down arrow keys to select the Zone Type

required then Press [OK] to save and exit or press [MENU] to

exit without saving.

Zone Type Zn001

01 - Burglary Delay 1

Press  0-9 OK to SAVE

0 – Zone Not Used

Program the zone type as zero if the zone is not being used.

1 – Burglary Delay 1

Zones programmed as Delay 1 will cause Entry Timer 1 to start when

tripped. The user must disarm the area before entry timer expires

or an alarm will occur. Zones set as Burglary Delay 1 are only active

when the area is armed. See MENU 7-2-1 — Entry Time 1 to set the

required delay time.

2 – Burglary Delay 2

Zones programmed as Delay 2 will cause Entry Timer 2 to start when

tripped. The user must disarm the area before entry timer expires

or an alarm will occur. Zones set as Burglary Delay 2 are only active

when the area is armed. See MENU 7-2-2 — Entry Time 2 to set the

required delay time.

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 44

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64