Bosch Solution 64 Specifications download pdf (Page 48)

Solution 64

Installer Guide

Input Programming

7-8

Bosch Security Systems | 11/05 | BLCC110I

Inputs > Zone Properties >

Zone Options



MENU 3-1-8

1 Lockout Siren Y

2 Silent Alarm N

3 Inverted Seal N

4 Bypass Allowed Y

5 Sensor Watch N

6 Armed When in Part Mode 1 Y

7 Reserved N

8 Test On Exit Y

The above options are programmable per zone.

Press [MENU] + [3] + [1] + [8] and use the up and down arrows

to highlight the Zone in the list then press [OK]. Alternatively,

you can enter the zone number directly and press [OK]. The

keypad will display the Report Options for the currently

selected zone.

Use the up and down arrow keys to highlight the option then

press the [ON] key to enable or the [OFF] key to disable.

 Lockout Siren

Silent Alarm

Inverted Seal

Press  OK ON OFF MENU

Repeat Step 2 until all options are programmed as required,

then press [OK] to save and exit or press [MENU] to exit

without saving.

Lockout Siren

Setting this option will enable Siren Lockout functionality for the

respective zone(s). All zones in the system can be individually

programmed for Siren Lockout.

When enabled the respective zone will be allowed to cause the

sirens to sound each time a new alarm is triggered provided that the

Swinger Siren count has not been reached. If the zone is triggered and

the Swinger Siren count has been reached then the siren will become

locked out for that zone and no further siren activations will occur

from that zone. Only zones which have been locked out are prevented

frrom triggering the sirens.

Siren lockout will be reset on the next arming cycle.

See MENU 7-4-3 — Swinger Siren to set the shutdown count.

Silent Alarm

Setting this option will set the correspondiing zone to become a silent

zone. Audible alarm outputs will not sound when a silent zone is

triggered.

Inverted Seal

Setting this option allows a normally-open sensor or device to operate

as a normally-closed device by reversing the open/closed state of the

zone loop. (eg. When the zone loop is open, the system will register

the zone loop as closed or normal.)

Bypass Allowed

Setting this option allows users with the appropriate access level to

manually bypass this zone eectively removing it from the area for

the current arming cycle. All zone types including 24hour zones can

be bypassed if this option is selected. Bypassed zones will be reset

when the area is turned o or disarmed.

Sensor Watch

Setting this option causes the system to monitor the zone’s activity

while the corresponding area is in the disarmed state. If the zone

fails to unseal and reseal at least once during the Sensor Watch

Time period a system trouble will be displayed on the keypad and a

Sensor Watch report for the corresponding zone will be sent to the

programmed destination. See MENU 3-9-2 — Sensor Watch to set the

time period.

Note

Sensor Watch monitoring is only active when the area is in the

disarmed state. 24 hour zone types cannot be monitored using

the Sensor Watch feature.

Armed When In Part Mode 1

Setting this option causes the zone to be active or monitored when

the corresponding area is armed in Part On Mode 1.

If this option is not set, the corresponding zone will be inactive when

the area is armed in Part Mode 1 allowing users to move freely within

this zone and not trigger an alarm.

Test On Exit

Setting this option will cause the system to prompt the user that a

zone or zones are not sealled when they attempt to arm the area in

which the zone belongs. An error beep will sound and a zone trouble

message will display on the keypad advising the user to seal the

zone(s) or to bypass them before the area will arm.

If this option is disabled the zone will not be tested during the arming

sequence and the system will arm. If the zone(s) are unsealled at the

end of exit time a Zone Trouble report will be sent.

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 48

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64