Bosch Solution 64 Specifications download pdf (Page 49)

Solution 64

Installer Guide

Input Programming

Bosch Security Systems | 11/05 | BLCC110I

7-9

Adding RF Sensors

The Solution 64 panel supports a wide range of 3rd party

wireless movement sensors, door contacts and smoke

detectors allowing you to choose the most appropriate devices

for each installation.

There are basically two dierent methods for adding RF

devices to the Solution 64, Direct Entry and Learn Mode. The

system will prompt for the appropriate method depending on

the Receiver type you have tted.

In all cases the RF sensor must be compatible with the RF

Receiver that is installed. See MENU 3-5-0 — Input Type.

Note

Zones congured as RF zone will follow all other zone

properties.

RF Sensor - Direct Entry Mode

Inputs > RF Zone >

Add RF Device



MENU 3-3-0

This menu allows you to program an RF device to a zone. Only

one device can be connected to each zone up to a maximum

of 64 RF devices per system.

Press [MENU] + [3] + [3] + [0] and use the up and down arrows

to highlight the zone you want to program in the list and

press[OK]. Alternatively, you can enter the zone number

directly and press [OK]. The system will only list zones that

dont already have an RF device programmed.

Enter Zone RFid for

Z001 Zone 1 Name

000000000

Press OK or MENU

Using the numeric keys, enter the RF device ID number.

Press [OK] to save and exit or press [MENU] to exit without

saving.

Inputs > RF Zone >

Delete RF Device



MENU 3-3-1

This menu allows you to delete an RF device .

Press [MENU] + [3] + [3] + [1] and use the up and down arrows

to highlight the zone in the list and press[OK]. The keypad will

only list zones that have an ID programmed. If no zones have

an ID number programmed, the keypad will display:

No Matching List Items

Found!

Press  OK ON OFF MENU

OK to delete RF zone for

Zn001 Zone 1 Name

007407097

Press OK or MENU

Press [OK] to DELETE the RF device and exit or press [MENU] to

exit without deleting.

RF Sensor - Learn Mode

Press [MENU] + [3] + [3] + [0] and use the up and down arrows

to highlight the zone you want to program in the list and

press[OK]. Alternatively, you can enter the zone number

directly and press [OK].

The system will only list zone that dont already have and RF

device programmed.

Enter Zone RFid for

Zn001 Zone 1 Name

000000000

Press OK or MENU

Trigger the RF sensor so that transmits a valid signal.

Once the device code has been leartn the system will

automatically exit and return to the menu.

Note

Make sure that only one device is triggerred when the system is

in learn mode. Devices that have already been learnt cannot be

learnt again unless they are deleted from the system rst.

Inputs > RF Zone >

Test RF Device



MENU 3-3-2

This menu allows you to test just how good the current

position is for an RF device. Enter the command and you will

be presented with a list of RF zones in the current area that are

available for test. Use the arrow keys to highlight the zone to

test and press OK. At any time press menu to exit.

Press [MENU] + [3] + [3] + [2] and use the up and down arrows

to highlight the zone you want to test in the list and press[OK].

Alternatively, you can enter the zone number directly and

press [OK]. The system will only list RF zones in the current

area.

Zn002 Zone 2 Name

Waiting For Trigger

Press OK or MENU

Once a signal is received the following information will be

displayed.

Zn002 Zone 2 Name

Transmission = 001

Signal = Good

Press OK or MENU

Signal can = Good, Average or Relocate

Every time you send a transmission, the number of

transmissions will increment and the average of the signals

with be displayed. Be sure to send a few transmission to

establish a more accurate signal measurement.

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 49

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64