Bosch Solution 64 Specifications download pdf (Page 54)

Solution 64

Installer Guide

Output Programming

8-2

Bosch Security Systems | 11/05 | BLCC110I

Output 1 Name Op001

Output Is Off

To Turn ON, Press ON

To Go Back Press OK

The keypad will display the following when the output is on. To

turn the output O, press [OFF].

Output 1 Name Op001

Output Is ON

To Turn OFF, Press OFF

To Go Back Press OK

Press [OK] or [MENU] when nished.

Output Properties

Outputs > Properties >

Output Name





MENU 4-1-0

O u t p u t 1 N a m e

This menu allows you to program the name for each output.

Output names can be up to 16 characters long.

Enter [MENU] + [4] + [1] + [0] and use the up and down arrows

to highlight the Output in the list then press [OK].

Alternatively, you can enter the output number directly and

press [OK].

Use the arrow and number keys to move and change text.

When the Output Name is complete, press [OK]. At any time

you can press the [OFF] key to clear the text from the current

cursor position to the end of the line.

Output Name Op001

Output 1

Press  OK to SAVE

Note

See Alpha Text Programming in Section 4 — Programming

Overview for further detail on entering alpha text.

Outputs > Properties >

Event Type



MENU 4-1-1

0 0 0

This menu allows you to set the output even type. See the

Output Event Type Table and Event Type Descriptions in this

section for more information on the available options.

Press [MENU] + [4] + [1] + [1] and use the up and down arrows

to highlight the Output in the list then press [OK].

Alternatively, you can directly enter the output number and

press [OK].

Use the up and down arrow keys to select the Event Type

required then Press [OK] to save and exit or press [MENU] to

exit without saving. It is also possible to directly enter the

Event Type number then Press [OK].

Event Type Op001

36 - External Audible

Press 0-9 OK to SAVE

1 - Battery Trouble

This event type will cause the output to operate when the panel

detects a low or missing stand-by battery and will reset once a

successful battery test has been performed.

Battery tests are performed automatically every 4 hours and when

the system is armed. A manual test can also be requested at any time

while the system is disarmed. See MENU 7-9-1 — Battery Test

2 – AC Trouble

This event type will cause the output to operate when the panel

detects that the AC mains power has been missing for 1 minute and

will reset when the power has been restored for 1 minute.

3 – Telephone Line Trouble

This event type will cause the output to operate when the panel

detects that the telco line has been disconnected for 30 seconds and

will reset when the line has been restored.

4 – Comm Fail – Destination 1 / 2

This event type will cause the output to operate if the panel fails to

report a signal to report destination1 or 2 or both. The panel will try

to send the report as many times as set in the call attempt counter

before registering a comm fail.

The output will restore as soon as a successful report has been

sent to the destination that has previously failed to report. If both

Destination 1 and Destination 2 had failed to report then successful

report to both destinations will need to be made before the output

will reset. See MENU 5-2-0 — Call Attempt Count

5 – Third Failed Dialler Attempt

This event type will cause the output to operate when the panel has

made 3 unsuccessful call attempts to the base station. The output

will reset when all pending messages have been sent or when the

maximum number of call attempts have been made.

6 – Destination 1 Reporting

This event type will cause the output to operate when the panel is

communicating to Destination 1 and will reset when the transmission

ends.

7 – Destination 2 Reporting

This event type will cause the output to operate when the panel is

communicating to Destination 2 and will reset when the transmission

ends.

8 – Destination 1/2 Kiss-Off

This event type will cause the output to operate when the panel

receives an kiss-o acknowledgment from the receiving party while

communication to destination 1 or 2. It is recommended that this

output is programmed with a one-shot timer.

9 – Destination 1 Kiss-Off

This event type will cause the output to operate when the panel

receives a kiss-o acknowledgment from the receiving party while

communicating to destination 1. It is recommended that this output

is programmed with a one-shot timer.

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 54

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64