Bosch Solution 64 Specifications download pdf (Page 55)

Solution 64

Installer Guide

Output Programming

Bosch Security Systems | 11/05 | BLCC110I

8-3

10 – Destination 2 Kiss-Off

This event type will cause the output to operate when the panel

receives a kiss-o acknowledgment from the receiving party while

communicating to destination 2. It is recommended that this output

is programmed with a one-shot timer.

11 – Dialler Disabled

This event type will cause the output to operate if the panel reporting

functions are manually disabled and will reset when reporting is

enabled. See MENU 5-2-1 — Dialer Options.

12 – Horn Speaker Missing

This event type will cause the output to operate when the panel

detects that a horn speaker is missing. The output will reset when

the horn speaker is reconnected. Only output 1 and 2 can be

programmed as a horn speaker outputs. See MENU 4-1-3 — Output

Polarity for information on conguring an output to drive a horn

speaker

13 – Output Trouble

This event type will cause the output to operate when the panel

detects that an output device is missing or in an overload condition.

The output will reset when all failed outputs have restored or the

overload condition has been removed.

14 – Panel On-Line

This event type will cause the output to operate when the panel

seizes the phone line and will reset when the phone line is released.

15 – Incoming Call

This event type will cause the output to operate when the panel

detects an incoming call on the phone line and will reset when the

ring signal stops.

16 – System Trouble

This event type will cause the output to operate when the panel

detects a system trouble condition and will reset when the condition

is cleared.

17 – Box Tamper

This event type will cause the output to operate when the panel

detects that the onboard enclosure tamper circuit is open. The output

will reset when the tamper circuit is closed. No EOL resistor is required

on this input.

18 – Zone Trouble

This event type will cause the output to operate when the panel

detects that a zone has a trouble condition and will reset when the

trouble condition has cleared.

19 – Zone Mirror

This event type will cause the output to operate when a specic zone

is open or unsealled and will reset when the zone closes.

See MENU 4-1-2 — Event Assignment for infomation on how to set

the zone to mirror.

20 – Zone Alarm

This event type will cause the output to operate when a specic zone

has triggered an alarm and will reset when the corresponding area is

disarmed. For a non 24hour zone to trigger an alarm the area must be

armed. See MENU 4-1-2 — Event Assignment for infomation on how

to set the zone to monitor.

21 – Area Disarmed

This event type will cause the output to operate as soon as the

corresponding area is disarmed and will reset when the area is armed

in either the All On or Part On modes.

If the output event assignment for this output is set to zero (all areas),

then all areas must be disarmed for the output to operate. The output

will reset as soon as any area is armed in either the All On or Part On

modes.

22 – Area Armed (Any)

This event type will cause the output to operate when the selected

area is armed in either All On or Part On mode. The output will reset

when the area is disarmed.

If the event assignment for this output has been set to zero (all areas)

then the output will only operate when all areas have been armed

in All On or Part On mode. The output will reset as soon any area is

disarmed.

23 – Area All On

This event type will cause the output to operate as soon as a specic

area is armed All On mode and will reset when the area is disarmed.

If the event assignment for this output has been set to zero (all areas),

then the output will only operate when all areas have been armed in

the All On mode and will reset as soon as any area is disarmed.

24 – Area Part On

This event type will cause the output to operate as soon as a specic

area is armed Part On mode and will reset when the area is disarmed.

If the event assignment for this output has been set to zero (all areas),

then the output will only operate when all areas have been armed in

the Part On mode and will reset as soon as any area is disarmed.

25 – Area Part 2 On

This event type will cause the output to operate as soon as a

specic area is armed Part 2 On mode and will reset when the ares is

disarmed.

If the event assignment for this output has been set to zero (all areas),

then the output will only operate when all areas have been armed in

the Part 2 On mode and will reset as soon as any area is disarmed.

26 – Entry Time

This event type will cause the output to operate while either Entry

Timer 1, Entry Timer 2 or the Part Mode Entry Timer is active. The

output will reset when the entry timer expires or the corresponding

area is disarmed.

27 – Exit Time

This event type will cause the output to operate while Exit Timer

is active. The output will reset when the exit timer expires or the

corresponding area is disarmed.

28 – End Of Exit Time

This event type will cause the output to operate when the Exit Time

expires and will reset when the corresponding area is disarmed.

29 – Chime On

This event type will cause the output to operate when Chime Mode is

activated and will reset when Chime Mode is turned o.

If the event assignment for this output is set to zero (all areas), then

the output will operate as soon as Chime Mode is activated in any

area and will reset when Chime Mode is turned o in all areas.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 55

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64