Bosch Solution 64 Specifications download pdf (Page 56)

Solution 64

Installer Guide

Output Programming

8-4

Bosch Security Systems | 11/05 | BLCC110I

30 - Chime Zone Faulted

This event type will cause the output to operate when a specic

Chime Zone is triggered and reset when the Chime Zone reseals.

If the event assignment for this output is set to zero (all areas), then

the output will operate as soon as any chime zone is triggered

provided that Chime Mode is on in those areas. The output will reset

when all Chime Zones are resealed. For this event type to work Chime

Mode must be turned on. See MENU 2-0-5 — Chime On/O

31 – Auto Arm Pre-Alert

This event type will cause the output to operate when the Auto Arm

Pre-Alert Timer is active and reset when the Pre-Alert Timer expires or

a valid user code is entered.

32 – Ready To Arm All On

This event type will cause the output to operate when the area is

disarmed and all zones in the area are sealled. The output will reset

when the area is armed or when a zone becomes unsealled.

If the event assignment for this output is set to zero (all areas), then

the output will only operate if all areas are disarmed and all zones

are sealled. The output will reset if any area is armed or if any zone

becomes unsealled.

33 – Ready To Arm Part On

This event type will cause the output to operate when the area is

disarmed and all zones in the area which are to be monitored in Part

On mode are sealled. The output will reset when the area is armed or

when a Part On zone becomes unsealled.

If the event assignment for this output is set to zero (all areas), then

the output will only operate if all areas are disarmed and all Part On

zones are sealled. The output will reset if any area is armed or if any

Part On zone becomes unsealled.

34 – Ready To Arm Part 2 On

This event type will cause the output to operate when the area is

disarmed and all zones in the area which are to be monitored in Part 2

On mode are sealled. The output will reset when the area is armed or

when a Part 2 On zone becomes unsealled.

If the event assignment for this output is set to zero (all areas), then

the output will only operate if all areas are disarmed and all Part 2 On

zones are sealled. The output will reset if any area is armed or if any

Part 2 On zone becomes unsealled.

35 – ‘Close’ Report Sent OK

This event type will cause the output to operate when the Closing

report has been acknowledged (Kissed-O) by the control room

receiver. The output will reset when the area is disarmed. If the

output has been assigned to multiple areas then it will only reset

when all areas have been disarmed.

36 – External Siren (Spk Beeps)

This event type will cause the output to operate when any audible

alarm occurs. The output will reset when the system or area is

disarmed.

This event type will also generate speaker beeps when the system or

area is armed via a RF Keyfob, the Programmable Input Terminal or

Keyswitch zone.

1 beep when the area is disarmed

2 beeps when the area is armed All On

3 beeps when the area is armed Part On



37 – Internal Siren

This event type will cause the output to operate when any audible

alarm occurs. The output will reset when the system or area is

disarmed. No speaker beeps are generated for this event type.

38 – Alarm Any (Silent or Audible)

This event type will cause the output to operate when any silent or

audible alarm occurs. The output will reset when the system or area is

disarmed

39 – Fire Alarm

This event type will cause the output to operate when any audible re

zone or keypad emergency re alarm occurs. The output will reset

when the system or area is disarmed.

40 – Burglary Alarm

This event type will cause the output to operate when any audible

burglary alarm (including keypad emergency panic, medical and

tamper alarm) occurs. The output will reset when the system or area

is disarmed.

41 – Silent Alarm

This event type will cause the output to operate when any silent alarm

occurs (including silent re and silent keypad emergency alarms). The

output will reset when the system or area is disarmed.

42 – Duress Alarm

This event type will cause the output to operate when a user initiates

a Duress alarm.

43 – Keypad Medical

This event type will cause the output to operate when a silent or

audible medical alarm has been initiated from the keypad. The

output will reset when the system or area is disarmed.

To initiate a medical emergency via the keypad, simultaneously press

and hold the [7] and [9] keys for 2 seconds.

44 – Keypad Fire

This event type will cause the output to operate when a silent or

audible re alarm has been initiated from the keypad. The output will

reset when the system or area is disarmed.

To initiate a re emergency via the keypad, simultaneously press and

and hold the [4] and [6] keys for 2 seconds.

45 – Keypad Panic

This event type will cause the output to operate when a silent or

audible panic alarm has been initiated from the keypad. The output

will reset when the system or area is disarmed.

To initiate a panic emergency via the keypad, simultaneously press

and hold [1] and [3] keys.

46 – Keypad Tamper

This event type will cause the output to operate when the tamper

circuit on the rear of the keypad is triggered. The output will reset

when a valid user PIN is entered.

47 – Access Denied

This event type will trigger if you attempt to enter an incorrect code

more times than programmed in the pin retry count location. The

event assignment will be the area number for this event type.

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 107 108

Comments to this Manuals

No comments

Bosch Solution 64 Specifications Page 56

Comments to this Manuals

Related products and manuals for Power tools Bosch Solution 64