Bosch D9112B Installation Manual Page 56
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9112B | Program Entry Guide | 3.0 User Interface EN | 56
Bosch Security Systems | 2/04 | 74-06145-000-D
L## Chg Passcode
Default: See
Program Record Sheet
Selection: Blank or E
Change Passcodes:
See Authority Level Selections in the introduction to the
Authority Lvl Assign programming module for
descriptions of selections.
Add Passcode
Default: P
Selection: Blank, E, or P
Add Passcode [COMMAND] [5] [6]:
Add user numbers, associated passcodes, and assign
authority levels for each area. This is a panel-wide
function that can be executed from any command
center assigned to an area where the user has
authority.
Bosch Security Systems recommends this item be
programmed P or disabled.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Add Passcode
Default: See
Program Record Sheet
Selection: Blank or E
Add Passcode: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
Del Passcode
Default: P
Selection: Blank, E, or P
Delete Passcode:
Delete user numbers and associated passcodes from
the system. This is a panel-wide function that can
be executed from any command center assigned to
an area where the user has authority.
Bosch Security Systems recommends this item be
programmed P or disabled.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Del Passcode
Default: See
Program Record Sheet
Selection: Blank or E
Delete Passcode: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
Extend Close
Default: P
Selection: Blank, E, or P
Extend Close:
Change the expected closing time for the area where
the function is entered. The window cannot be
adjusted until the
Close Early Begin
time has
passed and the closing window is active.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Extend Close
Default: See
Program Record Sheet
Selection: Blank or E
Extend Close: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
View Log
Default: E
Selection: Blank, E, or P
View Log: This is a panel-wide function that can
be executed from any command center assigned to
an area where the user has authority.
This command center function allows the user to
view all of the events stored in the D9112 log. This
is particularly useful for system troubleshooting.
Every time an event is generated, the event is sent to
the log. Many events have “modifiers” attached to
them. Modifiers are stored in the log as separate
events. For example, each time an area is force
armed several events are sent to the log.
The log in the D9112 can store up to 499 events
panel-wide. When the number of stored events
exceeds 499, the panel overwrites the oldest event,
regardless of the area in which it occurred. See
Log
% Full
in RAM Parameters for more information
about the event log.
- Control Panel 1
- About this Guide 2
- Other Lettering Conventions 2
- Used in this Manual 2
- Table of Contents 3
- Table of Tables 7
- 1.0 Panel Wide Parameter 8
- Point/User Flag 9
- A# Acct O/C 9
- A# Area O/C 9
- P### BFSK/Relay 9
- Modem Format 10
- Default: 11
- 1.2 Phone Routing 12
- 1.3 Power Supervision 19
- 1.4 Printer Parameters 20
- PRT Non Alrm 21
- SDI Fail 21
- Diagnostic 21
- Expanded Test 21
- 1.5 RAM Parameters 22
- Log % Full 24
- RAM Call 24
- Bad Call to RAM 24
- 2.0 Area Wide Parameters 25
- 2.2 Bell Parameters 27
- 2.3 Opening and Closing 29
- 2.4 O/C Windows 35
- Xept Holiday 39
- W## Xept Holiday 39
- 2.5 Command Center 42
- CF# Text 44
- CF# Key Stroke 44
- Program Record Sheet 44
- 3.0 User Interface 45
- 3.3 Cmd Center Function 46
- 3.4 Authority Lvl Assign 46
- Point Type 51
- Perimeter O/C 51
- Perimeter 51
- Closing Options 60
- 4.0 Command Menu 62
- 5.0 User Access Windows 64
- Windows 65
- 6.0 Passcode Worksheet 66
- Usr Code Tamper 67
- 7.0 Point Index 69
- Response 70
- Point Response 70
- P## Entry Delay 70
- 72
- A# Burg Time 74
- Fire Point 74
- 1. Program point 75
- 2. Choose a 75
- 3. Enable and/or disable 75
- 8.0 Point Assignments 79
- 8.2 Command 9 80
- 8.3 Command 7 81
- 9.0 Relay Parameters 82
- 9.1 Area Wide Relays 83
- 9.2 Panel Wide Relays 85
- 10.0 Skeds 86
- S## Area 1 87
- Bypassable 88
- Unbypass Point 88
- Unbypass All 88
- S## Defer Test 90
- S## Hourly Report 90
- S## Defer Status 90
- S## Cmd Center 91
- S## Custom Func 91
- 11.0 Holiday Indexes 94
- 11.2 View Holidays 95
- Bosch Security Systems 96
- 130 Perinton Parkway 96
- Fairport, NY 14450-9199 96
Related products and manuals for Security access control systems Bosch D9112B
(5 pages)
(8 pages)
(2 pages)
(12 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.777 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals