Bosch D9112B Installation Manual Page 71
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9112B | Program Entry Guide | 7.0 Point Index EN | 71
Bosch Security Systems | 2/04 | 74-06145-000-D
4
There are two ways to use
Point Type
4 to arm and disarm an area:
Keyswitch Maintain: Program
Point Response
as 1. Do not connect initiating devices to a
Keyswitch point.
Normal: The area is disarmed
Open: When this point changes from normal to open, the area arms.
Short: A short is a trouble while the area is disarmed.
• A short is an alarm while the area is armed.
• When this point changes from shorted to normal or open, it restores.
Trouble
and
Restoral
reports are not sent if
Local Disarmed
is YES.
Alarm
and
Restoral
reports are not sent if
Local Armed
is YES.
D279: Program
Point Response
as 2. The D279 should be the ONLY point in the area. The scope
of an account command center should be programmed to include the D279’s area.
Cut the W1 jumper on the D279 to send
Area
Opening
and
Closing
reports as programmed in
Area Parameters and to provide bell control. If the D279’s W1 jumper is NOT cut then no
Area
Open
or
Area
Close
report is sent, and alarm bells can only be silenced from a command center,
no matter how the D9112 is programmed.
Normal: When this point changes from open to normal, the area arms.
Open: The area is disarmed. The alarm bell silences if an alarm occurred while the area was
armed.
Short: A short is a trouble while the area is disarmed.
• A short is an alarm while the area is armed.
• When this point changes from shorted to normal or open, it restores but does not send a
Restoral
report.
5
Keyswitch Momentary: Used for Area Arming and Disarming.
Point Response
must be
programmed 1. Do not connect initiating devices to a Keyswitch point.
N→S→N: When this point momentarily changes from normal to shorted to normal, it toggles the
armed state of the area.
Open: An open is a trouble while the point is disarmed.
• An open is an alarm while the point is armed.
• When this point changes from shorted to normal to open, it restores.
Trouble
and
Restoral
reports are not sent if Local Disarmed is YES.
Trouble
and
Restoral
reports are not sent if Local Armed is YES.
6
Open/Close: Used for Point Arming and Disarming.
Point Response
must be programmed 1.
Local bells are silenced through the command center.
Normal: The point is armed and sends
Point Closing. Point Closing
is not sent if
Local Alarm
is
YES.
Open: An open is an alarm while the point is armed.
• An open is a trouble while the point is disarmed.
•
Alarm
and
Restoral
reports are not sent if
Local Disarmed
is YES.
Short: The point is disarmed and sends
Point Opening
. Local bells are silenced if they were
sounding.
Point Opening
is not sent if
Local Armed
is YES.
- Control Panel 1
- About this Guide 2
- Other Lettering Conventions 2
- Used in this Manual 2
- Table of Contents 3
- Table of Tables 7
- 1.0 Panel Wide Parameter 8
- Point/User Flag 9
- A# Acct O/C 9
- A# Area O/C 9
- P### BFSK/Relay 9
- Modem Format 10
- Default: 11
- 1.2 Phone Routing 12
- 1.3 Power Supervision 19
- 1.4 Printer Parameters 20
- PRT Non Alrm 21
- SDI Fail 21
- Diagnostic 21
- Expanded Test 21
- 1.5 RAM Parameters 22
- Log % Full 24
- RAM Call 24
- Bad Call to RAM 24
- 2.0 Area Wide Parameters 25
- 2.2 Bell Parameters 27
- 2.3 Opening and Closing 29
- 2.4 O/C Windows 35
- Xept Holiday 39
- W## Xept Holiday 39
- 2.5 Command Center 42
- CF# Text 44
- CF# Key Stroke 44
- Program Record Sheet 44
- 3.0 User Interface 45
- 3.3 Cmd Center Function 46
- 3.4 Authority Lvl Assign 46
- Point Type 51
- Perimeter O/C 51
- Perimeter 51
- Closing Options 60
- 4.0 Command Menu 62
- 5.0 User Access Windows 64
- Windows 65
- 6.0 Passcode Worksheet 66
- Usr Code Tamper 67
- 7.0 Point Index 69
- Response 70
- Point Response 70
- P## Entry Delay 70
- 72
- A# Burg Time 74
- Fire Point 74
- 1. Program point 75
- 2. Choose a 75
- 3. Enable and/or disable 75
- 8.0 Point Assignments 79
- 8.2 Command 9 80
- 8.3 Command 7 81
- 9.0 Relay Parameters 82
- 9.1 Area Wide Relays 83
- 9.2 Panel Wide Relays 85
- 10.0 Skeds 86
- S## Area 1 87
- Bypassable 88
- Unbypass Point 88
- Unbypass All 88
- S## Defer Test 90
- S## Hourly Report 90
- S## Defer Status 90
- S## Cmd Center 91
- S## Custom Func 91
- 11.0 Holiday Indexes 94
- 11.2 View Holidays 95
- Bosch Security Systems 96
- 130 Perinton Parkway 96
- Fairport, NY 14450-9199 96
Related products and manuals for Security access control systems Bosch D9112B
(5 pages)
(8 pages)
(2 pages)
(12 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 3.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals