Bosch D9112B Installation Manual Page 53
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9112B | Program Entry Guide | 3.0 User Interface EN | 53
Bosch Security Systems | 2/04 | 74-06145-000-D
Watch Mode
Default: E
Selection: Blank, E, or P
Watch Mode [COMMAND] [6]:
This command center function operates only in the
area where the command center is assigned. No
entry or exit delays are provided with this arming
function.
This function provides command center and
optional relay annunciation of faults from points that
are programmed as
Watch Points
in Point Index.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Watch Mode
Default: See
Program Record Sheet
Selection: Blank or E
Watch Mode: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
Perim Partial
Default: E
Selection: Blank, E, or P
This command center function arms only perimeter
points which are not faulted in the area where the
command center is assigned. Entry and exit delays
are provided with this arming function.
This function ignores the
A# FA Bypass Max
entry
in Area Parameters.
No
Closing
report is sent to the central station,
however, a Perimeter Delay event is recorded and
faulted points are identified as “forced” in the event
log.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Perim Partial
Default: See
Program Record Sheet
Selection: Blank or E
Perimeter Partial Arm: See Authority Level Selections
in the introduction to the Authority Lvl Assign
programming module for descriptions of selections.
View Area Stat
Default: P
Selection: Blank, E, or P
View Area Status: This command center function
allows the user to view the armed status of areas
other than the one to which the command center is
assigned. This function shows the following status for
areas where the passcode is authorized: armed,
disarmed, perimeter armed (partial, instant, delayed)
not ready to arm, account armed text, exit delay
text, entry delay text.
L## View Area Stat
Default: See
Program Record Sheet
Selection: Blank or E
View Area Status: See Authority Level Selections in
the introduction to the Authority Lvl Assign
programming module for descriptions of selections.
View Event Mem
Default: E
Selection: Blank, E, or P
View Event Memory [COMMAND] [4] [O]:
View prior alarm and trouble activity that occurred
during the last armed period. The user can view
activity in areas within the
Scope
of the command
center where the function is entered (see Cmd Cntr
Assignment). Event memory is not cleared until the
area is rearmed.
See Command Center Function Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
L## View Event Mem
Default: See
Program Record Sheet
Selection: Blank or E
View Event Memory: See Authority Level Selections
in the introduction to the Authority Lvl Assign
programming module for descriptions of selections.
- Control Panel 1
- About this Guide 2
- Other Lettering Conventions 2
- Used in this Manual 2
- Table of Contents 3
- Table of Tables 7
- 1.0 Panel Wide Parameter 8
- Point/User Flag 9
- A# Acct O/C 9
- A# Area O/C 9
- P### BFSK/Relay 9
- Modem Format 10
- Default: 11
- 1.2 Phone Routing 12
- 1.3 Power Supervision 19
- 1.4 Printer Parameters 20
- PRT Non Alrm 21
- SDI Fail 21
- Diagnostic 21
- Expanded Test 21
- 1.5 RAM Parameters 22
- Log % Full 24
- RAM Call 24
- Bad Call to RAM 24
- 2.0 Area Wide Parameters 25
- 2.2 Bell Parameters 27
- 2.3 Opening and Closing 29
- 2.4 O/C Windows 35
- Xept Holiday 39
- W## Xept Holiday 39
- 2.5 Command Center 42
- CF# Text 44
- CF# Key Stroke 44
- Program Record Sheet 44
- 3.0 User Interface 45
- 3.3 Cmd Center Function 46
- 3.4 Authority Lvl Assign 46
- Point Type 51
- Perimeter O/C 51
- Perimeter 51
- Closing Options 60
- 4.0 Command Menu 62
- 5.0 User Access Windows 64
- Windows 65
- 6.0 Passcode Worksheet 66
- Usr Code Tamper 67
- 7.0 Point Index 69
- Response 70
- Point Response 70
- P## Entry Delay 70
- 72
- A# Burg Time 74
- Fire Point 74
- 1. Program point 75
- 2. Choose a 75
- 3. Enable and/or disable 75
- 8.0 Point Assignments 79
- 8.2 Command 9 80
- 8.3 Command 7 81
- 9.0 Relay Parameters 82
- 9.1 Area Wide Relays 83
- 9.2 Panel Wide Relays 85
- 10.0 Skeds 86
- S## Area 1 87
- Bypassable 88
- Unbypass Point 88
- Unbypass All 88
- S## Defer Test 90
- S## Hourly Report 90
- S## Defer Status 90
- S## Cmd Center 91
- S## Custom Func 91
- 11.0 Holiday Indexes 94
- 11.2 View Holidays 95
- Bosch Security Systems 96
- 130 Perinton Parkway 96
- Fairport, NY 14450-9199 96
Related products and manuals for Security access control systems Bosch D9112B
(5 pages)
(8 pages)
(2 pages)
(12 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 0.277 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals