Bosch D9112B Installation Manual Page 54
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9112B | Program Entry Guide | 3.0 User Interface EN | 54
Bosch Security Systems | 2/04 | 74-06145-000-D
View Pt Status
Default: E
Selection: Blank, E, or P
View Point Status: View points assigned to the area
where the command center is assigned. This function
shows point text and the electrical condition
(normal, open, short) of each point in the area.
0101
0101
0101
Points 72 and 136 appear in the Point Status
List. Notice that text for Commands 7 and 9
is followed by a MISSING condition on point
72 and point 136. Points 72 and 136 serve
dual purposes. They are used for Command
7 and Command 9, and they are also used to
supervise the data expansion bus. When you
see that points 72 and 136 are missing, do
not be alarmed. When these points are
missing the point bus is normal.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## View Pt Stat
Default: See
Program Record Sheet
Selection: Blank or E
View Point Status: See Authority Level Selections in
the introduction to the Authority Lvl Assign
programming module for descriptions of selections.
Walk Test
Default: E
Selection: Blank, E, or P
Walk Test [COMMAND] [4] [4]:
Test controlled points in disarmed areas within the
Scope
of the command center without sending
reports to the central station.
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Walk Test
Default: See
Program Record Sheet
Selection: Blank or E
Walk Test: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
Fire Test
Default: P
Selection: Blank, E, or P
Fire Test [COMMAND] [5] [8]:
Test 24-Hour points in areas within the
Scope
of the
command center where the function is entered.
When a Fire Test is initiated one person can
typically test a fire system without assistance. The
following features are provided with the Fire Test
Mode:
• Central station report is transmitted when the
Fire Test Mode is initiated and when it is
terminated.
• Local alarm annunciation without report
transmission.
All reports from 24-Hour points within the
Scope of the command center are
suppressed during Fire Test.
• Automatic smoke detector reset (executing Reset
Sensors from the Function Menu is not required
after each device is tested).
• Command centers equipped with an alpha-
numeric display show a sequential count after
each point is activated and restored.
• Printed record of each alarm test response is
available if a local printer is installed and has the
Scope
required to record events from the area
being tested (D9131 Printer Interface required).
See Command Center Function Selections in the
introduction to the Command Center Functions
programming module for descriptions of selections.
L## Fire Test
Default: See
Program Record Sheet
Selection: Blank or E
Fire Test: See Authority Level Selections in the
introduction to the Authority Lvl Assign programming
module for descriptions of selections.
- Control Panel 1
- About this Guide 2
- Other Lettering Conventions 2
- Used in this Manual 2
- Table of Contents 3
- Table of Tables 7
- 1.0 Panel Wide Parameter 8
- Point/User Flag 9
- A# Acct O/C 9
- A# Area O/C 9
- P### BFSK/Relay 9
- Modem Format 10
- Default: 11
- 1.2 Phone Routing 12
- 1.3 Power Supervision 19
- 1.4 Printer Parameters 20
- PRT Non Alrm 21
- SDI Fail 21
- Diagnostic 21
- Expanded Test 21
- 1.5 RAM Parameters 22
- Log % Full 24
- RAM Call 24
- Bad Call to RAM 24
- 2.0 Area Wide Parameters 25
- 2.2 Bell Parameters 27
- 2.3 Opening and Closing 29
- 2.4 O/C Windows 35
- Xept Holiday 39
- W## Xept Holiday 39
- 2.5 Command Center 42
- CF# Text 44
- CF# Key Stroke 44
- Program Record Sheet 44
- 3.0 User Interface 45
- 3.3 Cmd Center Function 46
- 3.4 Authority Lvl Assign 46
- Point Type 51
- Perimeter O/C 51
- Perimeter 51
- Closing Options 60
- 4.0 Command Menu 62
- 5.0 User Access Windows 64
- Windows 65
- 6.0 Passcode Worksheet 66
- Usr Code Tamper 67
- 7.0 Point Index 69
- Response 70
- Point Response 70
- P## Entry Delay 70
- 72
- A# Burg Time 74
- Fire Point 74
- 1. Program point 75
- 2. Choose a 75
- 3. Enable and/or disable 75
- 8.0 Point Assignments 79
- 8.2 Command 9 80
- 8.3 Command 7 81
- 9.0 Relay Parameters 82
- 9.1 Area Wide Relays 83
- 9.2 Panel Wide Relays 85
- 10.0 Skeds 86
- S## Area 1 87
- Bypassable 88
- Unbypass Point 88
- Unbypass All 88
- S## Defer Test 90
- S## Hourly Report 90
- S## Defer Status 90
- S## Cmd Center 91
- S## Custom Func 91
- 11.0 Holiday Indexes 94
- 11.2 View Holidays 95
- Bosch Security Systems 96
- 130 Perinton Parkway 96
- Fairport, NY 14450-9199 96
Related products and manuals for Security access control systems Bosch D9112B
(5 pages)
(8 pages)
(2 pages)
(12 pages)
(122 pages)© 2020, manymanuals.com. All rights reserved. | 1.490 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals