Bosch D9412GV4 Installation Guide Page 101
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 101
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
Default Text
Determining the armed state of an area using the programmed custom text might be difficult.
Use this function to switch temporarily to the control panel default text, shown on the
program record sheet.
Change Skeds
Execute this panel-wide function from any keypad assigned to an area where the user has
authority. Use this function to change the S## Time from the keypad to make adjustments to
Skeds.
Invisible Walk Test
This function allows a user with the L## Invisible Walk Test authority to test invisible interior
or perimeter controlled points that are within the scope of the keypad, without sending
reports to the central station. Invisible points must have the P## Invisible Point function
programmed Yes.
3.12.4 Custom Functions
C Function 128 [through 143]
When enabled, Custom Function determines if a passcode is required when accessing a
custom function from the menu list. ENTER PASSCODE (or Enter Passcode + Enter Key on the
D1260) appears when this function is passcode protected. If a command within the Custom
Function is passcode protected, the keypad displays ENTER PASSCODE (or Enter Passcode +
Enter Key on the D1260) and waits for the user to enter a valid passcode before proceeding
with the rest of the Custom Function. If a passcode is not entered within 10 sec, the Custom
Function times out and the display returns to idle text.
3.12.5 Configuration Authority
Keypad Programming
Default: P
Selection: -, E, or P
Function No. Function Name Alternate Keystroke
34 Default Text [COMMAND][5][7]
Default: P
Selection: -, E, or P
Function No. Function Name Alternate Keystroke
35 Change Skeds [COMMAND][5][2]
Default: P
Selection: -, E, or P
Function No. Function Name Alternate Keystroke
36 Invisible Walk Test (Menu function only)
Default: P
Selection: -, E, or P
Function No. Function Name Alternate Keystroke
128 through 143 Enable Custom Functions
128 through 143
(Menu function only)
Default: P
Selection: - or P
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 0.401 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals