Bosch D9412GV4 Installation Guide Page 196
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
196 en | ACCESS CONTROL (D9412GV4/D7412GV4) D9412GV4/D7412GV4/D7212GV4
F.01U.218.312 | 04 | 2012.03 Program Entry Guide Bosch Security Systems, Inc.
Enter the keypad number (CC#) which determines the scope of the user ID’s disarming rights.
Areas disarm on the basis of this keypad’s scope and the authority level of the user.
D# Custom Function
You can program a custom function to run at the keypad programmed for CC# Scope. This
custom function activates only for users with an L## Function Level? Assignment (refer to
Section 3.12 User Interface, page 93) in which a valid ID can execute a custom function during
the armed or disarmed state. The user number to which the token is assigned must have an
assigned passcode.
If D# Disarm On Open is set to Yes for the same door, and L## Function Level? is set to D or
C, the custom function executes when the door is physically opened.
Table 9.1, Page 196 shows how this programming affects custom function activation.
Table 9.1 Effects of Programming on Custom Function Activation
D# Door Point
Enter the point number assigned to this door. This point cannot be used for any other point
assignments so the corresponding P### Point Source prompt is set to Door Point
automatically.
Default: 0 (Disabled)
Selection: 0, 128-143 (128-131 on the D7412GV4)
0 Custom function disabled.
128-143 The custom function number that executes upon a valid ID, given the
appropriate user access level and area arm state.
NOTICE!
A user’s access level and the armed state of the area determine whether the custom function
activates. This access level is programmed in the L## Function Level? prompt. Refer to
Section 3.12 User Interface, page 93.
L## Function Level? Custom Function Activation
M
(Armed)
User token activates the custom function assigned to the Door
Controller only while the entry area for the Door Controller is
Master Armed or Perimeter Armed.
D
(Disarmed)
User token activates the custom function assigned to the Door
Controller only while the entry area for the Door Controller is
disarmed.
C
(Armed and Disarmed)
User token activates the custom function assigned to the Door
Controller regardless of the armed state of the entry area.
- User token does not run the custom function assigned to the
Door Controller.
NOTICE!
A user’s security level must have an M, P, or D to operate the custom function.
Default: 0
Selection: 0 to 127, 129 to 247 (0 to 75 on the D7412GV4)
1 to 127, 129 to 247 The point number assigned to this door. Points 128 and 248 are
reserved by the control panel for internal use.
0 No point number is assigned to this door.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 1.514 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals