Bosch D9412GV4 Installation Guide Page 145
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Points | en 145
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
When initiated (either through a Fire Walk Test or the keypad’s Reset Sensor? function) or
when the remote programming software (RPS) interrupts power to the device for 5 sec, a
Sensor Reset report is sent to the central station receiver.
P## Alarm Abort
This parameter allows points with the associated Point Index to delay a Burglar Alarm (non-
fire) event for the time period specified in the Abort Window. An alarm is aborted by
performing an alarm silence operation at a keypad showing the burglar alarm condition before
this time elapses.
When an alarm is successfully aborted, the keypad shows an optional ALARM NOT SENT
message and no event is sent or written in the control panel event log. Refer to Section CC#
Abort Display, page 87.
For SIA CP-01 Compliance:
P## Alarm Abort can be set to Yes or No.
P## Wireless Point Supervision Time
A fire point follows the supervision rules if configured as a point device. Fire points have a
fixed supervision interval of 4 hours, regardless of Wireless Point Supervision Time setting. If
a Fire Point setting is Yes, then the Wireless Point Supervision Time setting must be set to 4
hours. This is an alternate supervision interval to the global System Supervision Time setting.
Refer to Section System Supervision Time, page 190.
NOTICE!
When a sensor reset occurs, the control panel does not accept alarms from any points with
P## Resettable programmed as Yes. During the 5-sec reset time, alarms from these points are
ignored.
Do not mix fire and intrusion devices on the same powered loop.
Default: Refer to the program record sheet
Selection: Yes or No
Yes If the point goes into an alarm condition, the system delays the alarm
report for the amount of time specified in the control panel-wide
parameter Abort Window.
No If the point goes into an alarm condition, alarm reports are sent
immediately.
NOTICE!
This feature does not apply to Fire Alarms or invisible point alarms.
Default Refer to the program record sheet
Selection: None, 4 hr, 12 hr, 24 hr, 48 hr, 72 hr
None No wireless point supervision.
4 hr Send a missing condition after 4 hr of no contact from the wireless
device.
12 hr Send a missing condition after 12 hr of no contact from the wireless
device.
24 hr Send a missing condition after 24 hr of no contact from the wireless
device.
48 hr Send a missing condition after 48 hr of no contact from the wireless
device.
72 hr Send a missing condition after 72 hr of no contact from the wireless
device.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 2.742 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals