Bosch D9412GV4 Installation Guide Page 53
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 53
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
P## Scope
Supervise this SDI address. Generate Trouble SDI ## Reports and local trouble annunciation if
a problem occurs with this printer or the SDI bus.
P## A1 [through A#] in Scope
Only available if P## Scope is programmed Custom. This program item determines if events
occurring in an area print at this printer.
P## Fire Events
Use this prompt to determine whether these events print at assigned printer.
P## Burglar Event
P## Access Event
P## User Event
P## Test Event
P## Diag Event
Default: No Printer
Selection: No Printer, Area, Account, Panel Wide, Custom
Panel Wide Printer prints all designated events that occur panel-wide. A panel-wide
printer can cross account boundaries.
Account Printer prints all designated events that occur within any area with the
same account number in which this printer is assigned.
Area Printer prints all designated events that occur in the area to which this
printer is assigned.
Custom Printer prints all events occurring in areas programmed Yes for this
prompt regardless of any boundary restrictions.
No Printer No printer installed at this address. If a printer is connected, data does
not print.
Default: No
Selection: Yes or No
Yes Include Area # Events in the scope of this printer.
No Does not include Area # Events in the scope of this printer.
NOTICE!
Refer to the report tables in Section 3.3 Routing, page 23 to identify the events that print.
Events programmed as No in Routing still print at the local printer. Individual events within
the report group cannot be suppressed for events printed at the local printer.
Default: Yes (Printer 1 only)
Selection: Yes or No
Yes All events in this group print at assigned printer.
No No events in this group print at assigned printer.
Default: Yes (Printer 1 only)
Selection: Yes or No
Default: Yes (Printer 1 only)
Selection: Yes or No
Default: Yes (Printer 1 only)
Selection: Yes or No
Default: Yes (Printer 1 only)
Selection: Yes or No
Default: Yes (Printer 1 only)
Selection: Yes or No
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 1.938 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals