Bosch D9412GV4 Installation Guide Page 177
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 AUXPARM | en 177
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
Passcode Length
During entry delay, the code is accepted when the last digit is pressed to disarm the area.
For SIA CP-01 Compliance:
Passcode Length must be set to 3, 4, 5, or 6.
Swinger Count
When a point has P# Swinger Bypass set to Yes, the value set in Swinger Count determines
the number of times the point is faulted erroneously within an hour before it is automatically
bypassed.
For SIA CP-01 Compliance:
P## Swinger Bypass can be Yes or No. If P## Swinger Bypass is Yes, Swinger Count must be
1 or 2.
Remote Warning
Upon remote arming, the output pulses on for 2 sec. Upon remote disarming, the output
pulses on, off, on, off for 2 sec each.
For SIA CP-01 Compliance:
NOTICE!
To meet UL requirements, the combined Entry Delay time and Abort Window time must not
exceed 60 sec. For Entry Delay time programming information, refer to Section P## Entry
Delay, page 134.
UL note: Maximum settings for residential use:
Exit Delay =120 sec
Entry Delay = 45 sec bell
Off-Premise Transmission = 60 sec
Maximum settings for commercial use:
Exit Delay = 120 sec no line security
Entry Delay = 60 sec bell
Off-Premise Transmission = 60 sec
The system must use both the bell and off-premise transmission.
Default 0
Selection: 0, 3, 4, 5, or 6
0 Disabled; sets a variable length for user passcodes, allowing for
backward compatibility
3, 4, 5, or 6 Sets a fixed length to all user passcodes.
Default 2
Selection: 1, 2, 3, or 4
1, 2 Number of fault or trouble bypasses allowed per hour for SIA CP-01
compliance.
3 Optional fault count
4 Value used for backward compatibility with previous control panel
operation.
Default No
Selection: Yes or No
Yes The system uses the Alarm Bell output to annunciate the arming and
disarming of an area through remote software, or a remote arming
device such as a key switch or keyfob.
No No remote warning occurs to annunciate the arming and disarming of
an area through remote software, or a remote arming device such as a
key switch or keyfob.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 2.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals