Bosch D9412GV4 Installation Guide Page 49
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 49
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access Keypad Programming
and navigate to the RPS PARAMETERS option. Press [ENT]. The keypad shows the RPS
PASSCODE option and the currently configured passcode.
2. Press [NEXT] twice to advance to the RPS IP ADDRESS option and press [ENT]. The
currently configured IP address shows.
3. An invisible editing cursor is enabled for the first byte.
4. The [PREV] button acts as a [Backspace] key. Press [PREV] to delete the characters of
the byte, and then enter the new byte numbers, or press [NEXT] to move to the next
byte.
5. Repeat Step 4 to enter the correct numbers for each byte.
6. Press [ENT] to save the changes.
When the keypad reads PARAMETER SAVED, your selection is configured.
7. When the keypad reads RPS IP ADDRESS, press [NEXT] to advance to the RPS IP PORT
option. The keypad shows the currently configured port number.
8. Press [ENT] to change the port number.
9. The [PREV] button acts as a [Backspace] key. Press [PREV] to delete the characters of
the port number and then enter the new port number.
10. Press [ENT] to save the changes.
When the keypad reads PARAMETER SAVED, your selection is configured.
D1260
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access Keypad Programming
and navigate to the RPS Parameters option. Press [ENTER]. The keypad shows the RPS
Passcode option and the currently configured passcode.
2. Press Phone Number softkey. The keypad shows the currently configured phone number
and the IP Address option.
3. Press the IP Address softkey. The currently configured IP address shows.
4. Press the Edit softkey to change the IP address.
5. The Previous and Next softkeys move the cursor through the bytes. The Backspace
softkey allows you to erase characters. The Clear softkey allows you to clear the entire IP
address. Use the softkeys and the number buttons on the keypad to enter the new IP
Address.
6. Press the Save softkey to save the changes.
When the keypad reads Parameter Saved, your selection is configured.
7. When the keypad reads RPS IP Address, press the Port Number softkey. The keypad
shows the currently configured port number.
8. Press the Edit softkey to change the port number.
9. The Backspace softkey allows you to erase characters. The Clear
softkey allows you to
clear the entire port number. Use the softkeys and the number buttons on the keypad to
enter the new port number.
10. Press the Exit softkey to save the changes.
NOTICE!
The keypad does not accept numbers 256 to 999.
NOTICE!
The keypad does not accept invalid byte numbers.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 4.506 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals