Bosch D9412GV4 Installation Guide Page 199
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 ACCESS CONTROL (D9412GV4/D7412GV4) | en 199
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
D# Shunt Time
Enter the amount of time that the Door point is shunted to allow a user to open the door. The
duration of time should be sufficient so that the opened door does not cause the point to
enter into a trouble, alarm, or faulted condition.
D# Buzz Time
Enter the amount of time the buzzer output sounds to notify the user that the strike was
activated and the door is ready to open. The buzzer stops as soon as the door is opened.
D# Extend Time
Enter the amount of time that strike, buzz, and shunt activation is prolonged if a door is left
open and the shunt time expires. At the end of the programmed extend time, the buzzer
continues to buzz until the door closes. If programmed, the point assigned to the door
indicates a trouble, alarm, or fault at the keypad.
D# Deactivate On Open?
Determines if the strike deactivates immediately upon physically opening the door.
Default: 10 sec
Selection: 0 to 240 sec
0 Shunt Time is not programmed for this door.
1 to 240 The shunt activates for the amount of time programmed.
Default: 2 sec
Selection: 0 to 240 sec
0 Buzz Time is not programmed for this door.
1 to 240 The buzzer sounds for the amount of time programmed.
NOTICE!
A separate buzzer is required. Many readers have an internal buzzer that is not affected by
Buzz Time.
Default: 10 sec
Selection: 0 to 30 sec
NOTICE!
The CLOSE DOOR # display on keypad does not activate if D# Extend Time is set to 0.
NOTICE!
Regardless of how the Door point is programmed, the system generates a Trouble Door Left
Open Event while the system is disarmed, and an Alarm Door Left Open Event if the system is
armed and the door is held open beyond Extend Time. Door Closed - Restoral Events are
generated after the door is held open past Extend Time and the door returns to normal.
Default: Yes
Selection: Yes or No
Yes Strike deactivates when the door is opened after a valid Access Granted
request.
No Strike remains activated for the amount of the programmed strike time
whether door is opened or closed.
NOTICE!
In order for this function to work, a point needs to be assigned to the door.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 2.769 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals