Bosch D9412GV4 Installation Guide Page 61
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 61
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
3.10 Area Parameters
This programming module contains three programming categories: Area Parameters, Bell
Parameters, and Open/Close Options.
3.10.1 Area Parameters
Enter the area number you are programming.
Area# Area On
Use this program item to enable or disable the area specified.
Refer to Section Keypad Programming of Area # On and Area# Account Number, page 61.
Area# Account Number
Determines the account number for this area. An account number must be assigned to each
active area.
Account numbers are used to group areas together. Each area can have a different account
number, or several areas can share the same account number. The control panel uses the
account number as a reference for arming and keypad text displays.
Contact ID: Only the last four digits are sent.
Modem IIIa
2
: Enter a four-digit or ten-digit number.
Keypad Programming of Area # On and Area# Account Number
D1255
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access Keypad Programming
and navigate to the AREA PARAMETERS option. Press [ENT].
2. The keypad reads AREA NUM 1 – 32 (1 – 8 for the D7412GV4).
3. Enter the area number you wish to configure and press [ENT]. The current area status
shows (for example, AREA 1 ON: YES).
4. Press [ENT] to change the area’s status.
Default: Yes (Area 1 only)
Selection: Yes or No
Yes Enable area
No Disable area
NOTICE!
Area 1 must be enabled:
– System events such as power and phone supervision do not send a report correctly if
Area 1 is disabled.
– When programmed No, points assigned to this area do not generate events, show at the
keypad when arming and disarming, or send status reports. All user authority in this area
is turned off while the area is disabled.
NOTICE!
To meet UL 864 requirements (D9412GV4 and D7412GV4), set A# Area On to Yes.
Default: 0000
Selection: For Modem format and Contact ID (four-digit account numbers): 0000
to 9999, BBBB to FFFF
For Modem format (ten-digit account numbers): 0000000000 to
9999999999, BBBBBBBBBB to FFFFFFFFFF
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 0.332 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals