Bosch D9412GV4 Installation Guide Page 131
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Points | en 131
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
3 Interior Follower: Interior Follower points are armed only by master arming the area. They are not
armed when using Perimeter-Arming functions.
An Interior Follower point does not create an alarm if it has a fault while the area is in entry delay. An
Interior Follower does not change the amount of remaining entry delay time.
If no entry delay is in effect when a fault occurs for the Interior Follower, it creates an instant alarm.
You must program a delayed Point Response (4, 5, 6, 7, or 8) for an Interior Follower point. The control
panel ignores the entry in P## Entry Delay for an Interior Follower point.
NOTICE!
Increasing the debounce count for Interior Follower points might be necessary to prevent Interior
Follower points from entering into alarm before the control panel recognizes that a Perimeter Delay
point was faulted. Program the Interior Follower’s debounce for one number higher than the debounce
count on Perimeter delay.
4* Keyswitch Maintained: Program P## Point Response as 1. Do not connect initiating devices to a
Keyswitch point.
Normal: The area is disarmed.
Short: A short is a trouble when the area is disarmed. A short is an alarm when the area is armed. When
this point changes from shorted to normal or open, it restores.
Open: When this point changes from normal to open, the area arms.
Program P## Point Response as 2, the point responds as follows:
Normal: When this point changes from open to normal, the area arms.
Open: The area is disarmed.
Short: A short is a trouble when the area is disarmed. A short is an alarm when the area is armed. When
this point changes from shorted to normal or open, it restores.
Trouble and Restoral Reports are not sent if Local While Disarmed is Yes.
Alarm and Restoral Reports are not sent if Local While Armed is Yes.
5* Keyswitch Momentary: Used for area arming and disarming. P## Point Response must be programmed
1. Do not connect initiating devices to a Keyswitch point.
N S N: When this point momentarily changes from normal to shorted to normal, it toggles the armed
state of the area.
Open: An open is a trouble while the point is disarmed. An open is an alarm while the point is armed.
When this point changes from open to normal, it restores.
Trouble and Restoral Reports are not sent if Local Disarmed is Yes.
6* Open/Close Point: Used for point arming and disarming. P## Point Response
must be programmed 1.
Local bells are silenced through the keypad.
Normal: The point is armed and sends a Point Closing Report. A Point Closing Report is not sent if Local
Armed is Yes.
Open: An open is an alarm when the point is armed. An open is a trouble when the point is disarmed.
Alarm and Restoral Reports are not sent if Local Disarmed is Yes.
Short: The point is disarmed and sends a Point Opening Report. A Point Opening Report is not sent if
Local Armed is Yes.
Default Refer to the program record sheet
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 4.000 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals