Bosch D9412GV4 Installation Guide Page 113
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
D9412GV4/D7412GV4/D7212GV4 Panel and Area Wide Parameters | en 113
Bosch Security Systems, Inc. Program Entry Guide F.01U.218.312 | 04 | 2012.03
L## C Function 128 [through 143]
Execute the desired Custom Function.
3.12.8 Report Levels
L## Force Arm
A user with this authority level can Force Arm.
L## Area O/C
Generates Opening and Closing Reports if the area where this authority level is assigned
sends Opening and Closing Reports.
L## Restricted O/C
Generates an Opening Report if a bell is ringing or a Closing Report when force or bypass
arming. The area where this authority level is assigned must be programmed for restricted
openings and closings (refer to the A# Restrictd O/C prompt in Section 3.10.4 Open/Close
Options, page 69.
L## Perimeter O/C
Generates Perimeter Opening and Closing Reports if the area where this authority level is
assigned sends Perimeter Opening and Closing Reports. Refer to the A# Perimeter O/C
prompt in Section 3.10.4 Open/Close Options, page 69.
L## Send Duress
Generates a Duress Report if the area where this authority level is assigned sends duress.
(Refer to the A# Duress Enable prompt on in Section 3.10.4 Open/Close Options, page 69.)
L## Passcode Arm
Arm an area by entering a passcode and pressing [ENTER].
L## Passcode Disarm
Disarm an area by entering a passcode and pressing [ENTER].
Default: Authority Levels 1: Enabled (E)Authority Levels 2-15: Blank (-)
Selection: - or E
Function No. Function Name Alternate Keystroke
128 through 143 Enable Custom Function
128 through 143
(Menu function only)
Default: Authority Levels 1-6: Enabled (E)Authority Levels 7-15: Blank (-)
Selection: - or E
Default: Authority Levels 1-14: Enabled (E)Authority Level 15: Blank (-)
Selection: - or E
Default: Blank
Selection: - or E
Default: Authority Levels 1-14: Enabled (E) Authority Level 15: Blank (-)
Selection: - or E
Default: Authority Levels 1-14: Enabled (E)Authority Level 15: Blank (-)
Selection: - or E
Default: Authority Levels 1-6: Enabled (E) Authority Levels 7-15: Blank (-)
Selection: - or E
Default: Authority Levels 1-5, 14: Enabled (E) Authority Levels 6-13, 15: Blank (-)
Selection: - or E
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 1.704 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals