Bosch D9412GV4 Installation Guide Page 204
- Page / 210
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
204 en | Keypad Tools Menu (Options Not Available in RPS) D9412GV4/D7412GV4/D7212GV4
F.01U.218.312 | 04 | 2012.03 Program Entry Guide Bosch Security Systems, Inc.
11 Keypad Tools Menu (Options Not Available in RPS)
11.1 Service Bypass Menu
11.1.1 Setting Service Bypass (PT NUM 1-247)
D1255
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access the TOOLS MENU
and navigate to the SERVICE BYPASS option.
2. Press [ENT] to enter the SERVICE BYPASS option.
If no points are bypassed, NO PTS BYPASSED shows. Skip to Step 6. If points are
bypassed, a list of unbypassed points shows.
3. Press [NEXT] to advance through the points in service bypass.
4. Press [ENT] to select the point that needs to have service bypass removed.
5. Press [NEXT] to toggle the SERVICE BYPASS setting, then [ENT] to save.
6. Press [ENT] at the SERVICE BYPASS prompt. The PT NUM 1-247: prompt shows.
7. Press the point number followed by [ENT]. The PT-### SERVICE BYPASS: NO prompt is
shown.
8. Press [NEXT] to toggle the SERVICE BYPASS setting, then [ENT] to save. The keypad
reads POINT BYPASSED.
D1260
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access the Tools Menu and
navigate to the Service Bypass option.
2. Press [ENTER] to enter the Service Bypass option.
If no points are bypassed, No Points Bypassed shows. If points are bypassed, a list of
unbypassed points shows.
3. The number of points in service bypass are below the Point Num 1-247: prompt. Enter
the point number followed by [ENTER].
4. Press [ENTER] to make a selection. The keypad reads Point Bypassed.
11.1.2 Resetting Service Bypass
D1255
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access the TOOLS MENU
and navigate to the SERVICE BYPASS option.
2. Press [ENT] to enter the SERVICE BYPASS option.
The SERVICE BYPASS prompt alternates with the number of points in service bypass.
3. Press [NEXT] to advance through the points in service bypass.
4. Press [ENT] to select the point that needs to have service bypass removed.
5. Press [NEXT] to toggle the SERVICE BYPASS setting, then [ENT] to save.
6. Press [ESC] at any time to return to the list of points in service bypass to select another
or press [ESC] again to exit.
When the keypad reads PARAMETER SAVED, your selection has been configured.
D1260
1. Refer to Section 2.5.1 Keypad Programming Menu, page 12 to access the Tools Menu and
navigate to the Service Bypass option.
2. Press [ENTER] to enter the Service Bypass option.
The Service Bypass prompt alternates with the number of points in service bypass.
- D9412GV4/D7412GV4/D7212GV4 1
- Table of Contents 3
- 1 System Requirements 6
- 2 Introduction 7
- 2.5 Guide to Keypad Tools 11
- 2.5.1 Keypad Programming Menu 12
- 2.5.2 Service Bypass Menu 14
- 2.5.3 RF Points Menu 14
- 2.5.4 RF Repeaters Menu 15
- 2.5.5 RF Diagnostics Menu 15
- 2.5.6 IP Diagnostics Menu 16
- 3.1 Phone 17
- 3.2 Phone Parameters 19
- 3.3 Routing 23
- 3.3.1 Call Party Disconnect 24
- 3.3.4 Enhanced Routing 24
- Event Priority 26
- 3.3.8 Route Group Parameters 29
- 3.3.9 Communication Attempts 30
- 3.3.10 Route Group Categories 33
- Table 3.7 Burglar Reports 34
- Table 3.8 User Reports 34
- Table 3.11 RPS Reports 38
- Enhanced Communications 40
- Figure 3.1 Poll Rate Timeline 44
- 3.6 Power Supervision 50
- 3.7 Printer Parameters 52
- 3.8 RPS Parameters 54
- 3.9 Miscellaneous 59
- 3.10 Area Parameters 61
- Table 3.15 Verify Time 64
- 3.10.3 Bell Parameters 66
- 3.10.4 Open/Close Options 69
- 3.10.5 Arming Features 74
- 3.11 Keypad (Command Center) 78
- 3.11.2 Area Text 88
- 3.11.3 Custom Function 89
- 3.12 User Interface 93
- 3.12.4 Custom Functions 101
- 3.12.7 General Functions 108
- 3.12.8 Report Levels 113
- 3.12.9 Access Control Levels 114
- 3.13 Function List 116
- 3.14 Relay Parameters 117
- 3.14.1 Area Relays 118
- 3.14.2 Panel-Wide Relays 121
- 4.1.1 User Credentials 125
- 4.1.2 Passcodes 125
- 4.1.3 User Group Window 125
- 4.1.4 User Name 125
- 4.1.5 Tokens and Cards 126
- 4.1.6 Reporting and Logging 126
- 5 Points 130
- 5.2 Point Responses 132
- Table 5.1 Bypassing a Point 141
- 5.3 Point Assignments 146
- 5.4 Cross Point Parameters 149
- 5.5 COMMAND 7 and COMMAND 9 151
- 6 Schedules (Skeds) 154
- 6.1.2 User Group Windows 162
- 6.2 Schedules (Skeds) 164
- Table 6.2 171
- 6.3 Holiday Indexes 173
- 7 AUXPARM 174
- 7.2 Miscellaneous 175
- 8 SDI2 Modules 179
- 8.5 Wireless Repeater 190
- 9.1 Door Profile 195
- 9.2 Strike Profile 198
- 9.3 Event Profile 200
- 10 SIA CP-01 Quick Reference 203
- 11.1 Service Bypass Menu 204
- 11.2 RF Points Menu 205
- 11.2.3 Remove RF Point 206
- NOTICE! 207
© 2020, manymanuals.com. All rights reserved. | 4.817 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals